Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY

HEADLIGHT ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE NO. 1 HEADLIGHT BULB


    E226722
  1. Turn the No. 1 headlight bulb in the direction indicated by the arrow shown in the illustration, and remove it.

    NOTICE:
    Do not touch the bulb glass.



2. REMOVE NO. 2 HEADLIGHT BULB (for Halogen Headlight)


    E226734
  1. Turn the No. 2 headlight bulb in the direction indicated by the arrow shown in the illustration, and remove it.

    NOTICE:
    Do not touch the bulb glass.



3. REMOVE HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY (for HID Headlight)


    E226724
  1. Turn the headlight light control ECU sub-assembly in the direction indicated by the arrow shown in the illustration, and disconnect it.

    NOTICE:
    1. Do not apply excessive force using a tool.
    2. Do not damage the O-ring or allow it to become contaminated with foreign matter. If the O-ring is damaged or contaminated, water may get into the headlight assembly, resulting in a malfunction of the headlight light control ECU sub-assembly.



    E226726
  1. Turn the socket of the headlight light control ECU sub-assembly in the direction indicated by the arrow shown in the illustration, and remove it.

    NOTICE:
    Do not pull the headlight light control ECU sub-assembly with the socket connected.



4. REMOVE DISCHARGE HEADLIGHT BULB (for HID Headlight)


    E226728E01
  1. Release the set spring as shown in the illustration and remove the discharge headlight bulb.

    NOTICE:
    Do not touch the bulb glass.



5. REMOVE HEADLIGHT SOCKET COVER
  1. for Halogen Headlight:

    1. Remove the 2 headlight socket covers from the headlight unit.

  1. for HID Headlight:

    1. Remove the headlight socket cover from the headlight unit.



6. REMOVE FRONT TURN SIGNAL LIGHT BULB


    E226730
  1. Turn the front turn signal light socket with the front turn signal light bulb in the direction indicated by the arrow shown in the illustration, and remove them as a unit.

  1. Remove the front turn signal light bulb from the front turn signal light socket.



7. REMOVE CLEARANCE LIGHT BULB


    E226732
  1. Turn the clearance light socket with the clearance light bulb in the direction indicated by the arrow shown in the illustration, and remove them as a unit.

  1. Remove the clearance light bulb from the clearance light socket.



8. REMOVE HEADLIGHT LEVELING MOTOR (w/o AFS)


    E226736E01
  1. Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.
    Text in Illustration 
    *1
    Aiming Screw

    HINT:
    1. Turn the aiming screw until the headlight leveling motor can be moved in the direction indicated by the arrow (2) shown in the illustration.
    2. Make sure to remember the number of aiming screw rotations.

  1. Turn the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to disengage the pin.

    HINT:
    When removing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction indicated by the arrow (2) shown in the illustration.



    E226738E01
  1. Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration to disengage the shaft.
    Text in Illustration 
    *1
    Aiming Screw

    HINT:
    Make sure to remember the number of aiming screw rotations.

  1. Pull out the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration to remove it.



9. REMOVE HEADLIGHT LEVELING MOTOR (w/ AFS)


    E226740
  1. Turn the headlight leveling motor in the direction indicated by the arrow shown in the illustration to disengage the pin.

    HINT:
    For the headlight leveling motor RH, rotate it symmetrical to the directional arrow shown in the illustration.



    E191796
  1. Lower the tip of the headlight leveling motor to disengage it from the reflector and remove the headlight leveling motor.



10. REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING
  1. Remove the headlight leveling motor base packing.

    NOTICE:
    After the headlight leveling motor base packing is removed, be sure to replace it with a new one. Failure to do this may cause water ingress.



11. REMOVE GROMMET


    E226742
  1. Using needle-nosed pliers, remove the grommet.