Home › Power Source / Network ยท 1AZ-FE BATTERY / CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR DRIVE END FRAME BEARING


    A265344E02
  1. Using SST and a press, press in a new generator drive end frame bearing.

    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)
    Text in Illustration 
    *1
    Generator Drive End Frame Bearing



    A128620E05
  1. Fit the tabs on the bearing retainer plate into the cutouts on the generator drive end frame assembly to install the bearing retainer plate.
    Text in Illustration 
    *a
    Tab
    *b
    Cutout

  1. Install the 4 screws

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }



2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the generator drive end frame assembly on the generator pulley with clutch.

  1. Install the generator rotor assembly to the generator drive end frame assembly.



3. INSTALL GENERATOR PULLEY WITH CLUTCH
  1. Temporarily install the generator pulley with clutch onto the rotor shaft.

  1. Hold the generator drive end frame assembly in a vise between aluminum plates.



    A128069E03
  1. Confirm SST (A) and (B) shown in the illustration.
    Text in Illustration 
    *1
    SST (A)
    *2
    SST (B)

    SST
    09820-63021  



    A193955E02
  1. Place the rotor shaft end into SST (A).
    Text in Illustration 
    *1
    Rotor Shaft
    *2
    SST (A)



    A193956E02
  1. Fit SST (B) to the generator pulley with clutch.
    Text in Illustration 
    *1
    Generator Pulley with Clutch
    *2
    SST (A)
    *3
    SST (B)



    A194281E12
  1. Tighten the generator pulley with clutch by turning SST (B) in the direction shown in the illustration.
    Text in Illustration 
    *1
    SST (B)
    *2
    SST (A)
    *a
    Fulcrum Length
    255 mm (10.00 in.)

    Torque:
    without SST:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }
    with SST:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }

    NOTICE:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 100 mm (3.94 in.) and a torque wrench with a fulcrum length of 255 mm (10.00 in.) (Click here).
    2. The "with SST" torque value is effective when SST is parallel to the torque wrench
    3. Check that the generator drive end frame assembly is secured in the vise tightly.
    4. Hold SST (A) tightly during the operation.

  1. Remove SST from the generator assembly.

  1. Check that the generator pulley with clutch rotates smoothly.

  1. Install a new generator pulley cap to the generator pulley with clutch.



4. INSTALL GENERATOR COIL ASSEMBLY
  1. Place a new generator washer on the generator rotor assembly.



    A128621E05
  1. Using SST and a press, press in the generator coil assembly to the generator drive end frame assembly.

    SST
    09612-70100   (09612-07240)

  1. Install the cord clip with the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Install the 4 bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }



5. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    A079315E18
  1. While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the generator brush holder assembly hole .
    Text in Illustration 
    *1
    Pin



    A128622
  1. Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }



    A130537E04
  1. Pull out the pin from the generator brush holder assembly.
    Text in Illustration 
    *1
    Pin
    *a
    Pull out



6. INSTALL GENERATOR TERMINAL INSULATOR


    A128623
  1. Install the generator terminal insulator to the generator coil assembly.

    NOTICE:
    Pay attention to installation direction of the generator terminal insulator.



7. INSTALL GENERATOR REAR END COVER
  1. Install the generator rear end cover to the generator coil assembly with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }