SHIFT LEVER > REMOVAL |
| 1. REMOVE CONSOLE BOX ASSEMBLY |
| 2. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 10 claws and remove the front door scuff plate LH.
| 3. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 5. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 6. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 7. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 bolts <B>.
w/o Driver Side Knee Airbag:
![]() |
Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.
w/ Driver Side Knee Airbag:
![]() |
Disengage the 4 claws, 7 clips and 3 guides to remove the instrument panel sub-assembly.
| 8. REMOVE FRONT DOOR SCUFF PLATE RH |
| 9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 10. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Disconnect the front door opening trim weatherstrip RH.
| 11. REMOVE INSTRUMENT SIDE PANEL RH |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
| 12. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides.
Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.
| 13. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the bolt <B> and screw <C>.
Open the lower instrument panel door.
![]() |
Remove the 3 screws <C>.
![]() |
Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.
| 14. REMOVE FRONT CONSOLE UPPER PANEL GARNISH |
for Blank Type:
![]() |
Disengage the 2 claws and remove the front console upper panel garnish as shown in the illustration.
for 3 Switch Hole Type:
![]() |
Disengage the 2 claws as shown in the illustration.
Disconnect the each connector to remove the front console upper panel garnish.
| 15. REMOVE FRONT ASH RECEPTACLE ASSEMBLY |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the 2 clips as shown in the illustration.
Disconnect each connector to remove the front ash receptacle assembly.
| 16. REMOVE FRONT NO. 2 CONSOLE BOX INSERT |
for LHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 4 guides to remove the front No. 2 console box insert as shown in the illustration.
| 17. REMOVE CONSOLE BOX INSERT |
for RHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 4 guides to remove the console box insert as shown in the illustration.
| 18. REMOVE FLOOR CARPET BRACKET LH |
![]() |
Remove the 2 clips.
Disengage the 2 guides to remove the floor carpet bracket LH.
| 19. REMOVE NO. 1 CONSOLE BOX MOUNTING BRACKET |
![]() |
Remove the screw and No. 1 console box mounting bracket from the lower shift lever assembly.
| 20. REMOVE NO. 1 CONSOLE BOX DUCT |
![]() |
Remove the clip and No. 1 console box duct.
| 21. REMOVE LOWER SHIFT LEVER ASSEMBLY |
Move the shift lever to N.
![]() |
Disconnect the end of the transmission control cable assembly from the lower shift lever assembly.
Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.
![]() |
Disconnect the 3 clamps and 2 connectors.
![]() |
Remove the 4 bolts and lower shift lever assembly.
| 22. REMOVE SHIFT LEVER SUPPORT |
![]() |
Remove the 4 bolts and shift lever support.