STEERING LOCK SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
Using the intelligent tester, confirm the Data List items to help determine the cause of the problem.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift P Signal | Shift position (P) signal / ON or OFF | ON: Shift lever in P OFF: Shift lever not in P |
|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly / ON or OFF | ON: Steering unlocked (Engine switch on (ACC)) OFF: Steering locked (Engine switch off door opened) | This item can be used to determine the cause of problems when the steering does not lock or unlock.
|
| Str Lock/Unlock Wait T-Out | Steering lock or unlock malfunction / Yes or No | Yes: Steering lock/unlock timed out (Lock bar stuck, etc.) No: Steering locks/unlocks normally within specified time | The engine cannot be started when this item is "Yes". |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | State of certification ECU (smart key ECU assembly) IG power supply input / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | This item displays "OFF" when the engine switch is on (ACC). |
| #Codes | Number of DTCs / 0 to 255 | Number of stored DTCs displayed | - |
| Immobiliser*1 | State of immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset | Set: Engine immobiliser set (Engine switch off) Unset: Engine immobiliser unset (Engine switch on (ACC) or on (IG)) |
|
| Immobiliser*2 | State of immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset | Set: Engine immobiliser set (Engine switch off) Unset: Engine immobiliser unset (Engine switch on (ACC) or on (IG)) |
|
| Steering Lock Sleep Cond | Steering lock ECU sleep condition / Yes or No | - | - |
| Steering Lock Start Cond | Transmission state of steering lock ECU wake up signal / Yes or No | Yes: Wake up signal transmitted No: Wake up signal not transmitted | - |
| Engine Start Condition | State of engine start permission signal determined by steering lock ECU and sent to certification ECU (smart key ECU assembly) / OK or NG | OK: Engine start permitted NG: Engine start prohibited |
|
| Sensor Value | Record of malfunction of position sensor in steering lock actuator assembly / OK or NG(Past) | OK: No record of lock/unlock sensor malfunction in steering lock actuator assembly NG(Past): Record of lock/unlock sensor in steering lock actuator assembly turning ON at same time exists | When this item displays "NG", the sensor inside the steering lock actuator assembly may be malfunctioning, or there may be a mechanical malfunction. |
| Power Supply Short | Record of malfunction of signal sent to steering lock motor (steering lock actuator assembly) from certification ECU (smart key ECU assembly) (short circuit) / OK or NG(Past) | OK: No record of malfunction (short circuit) NG(Past): Record of malfunction (short circuit) exists | This item records malfunctions in the circuit between the certification ECU (smart key ECU assembly) and steering lock motor (steering lock actuator assembly). |
| Motor Driver Short | Record of malfunction of motor activation circuit in steering lock actuator assembly (short circuit) (DTC B2781 stored) / OK or NG(Past) | OK: No record of malfunction (short circuit) NG(Past): Record of malfunction (short circuit) exists | This item records malfunctions in the motor activation circuit inside the steering lock actuator assembly (short circuit). |
| Lock/Unlock Receive | Reception state of steering lock or unlock request signal from certification ECU (smart key ECU assembly) / Yes or No | Yes: Record of receiving lock or unlock request signal exists No: No record of receiving lock or unlock request signal | - |
| Lock Bar Stuck Error | Record of lock bar not properly unlocking after being commanded to unlock for certain amount of time / OK or NG(Past) | OK: No record of stuck lock bar NG(Past): Record of stuck lock bar exists | - |
| Push Start Error | Record of malfunction of push-start function due to steering lock actuator assembly / OK or NG(Past) | OK: No record of push-start function malfunction NG(Past): Record push-start function malfunction exists | - |
| Engine Start Request | Reception state of engine start permission signal determined by steering lock actuator assembly and sent to certification ECU (smart key ECU assembly) / OK or NG | OK: Receiving signal NG: Not receiving signal |
|
| S Code Check*1 | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
| L Code Check*1 | Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
| L Code Check*2 | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
| Unlock Request Receive*1 | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
| OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine NG: Except above |
|
| Unlock Request Receive*2 | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) / OK or NG
| OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine NG: Except above |
|
| Lock Request Receive*1 | Reception state of steering lock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
| OK: Within 10 seconds of opening any door with engine switch off and shift lever in P NG: Except above | If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Lock Request Receive*2 | Reception state of steering lock request signal by certification ECU (smart key ECU assembly) / OK or NG
| OK: Within 10 seconds of opening any door with engine switch off and shift lever in P NG: Except above | If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| S Code Check(Past)*1 | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) (Past) / OK or NG(Past) | OK: Verification result normal NG(Past): Verification result abnormal (Past) | - |
| L Code Check(Past)*1 | Verification result between ID code box (immobiliser code ECU) and steering lock ECU (Past) / OK or NG(Past) | OK: Verification result normal NG(Past): Verification result abnormal (Past) | - |
| L Code Check(Past)*2 | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (Past) / OK or NG(Past) | OK: Verification result normal NG(Past): Verification result abnormal (Past) | - |
| Steering Lock | State of whether steering lock ECU has determined steering is locked / Set or Unset | Set: Steering locked Unset: Steering unlocked | If this item displays "Unset", the steering does not lock. |
| Steering Unlock | State of whether steering lock ECU determined steering is unlocked / Set or Unset | Set: Steering unlocked Unset: Steering locked | If this item displays "Unset", the steering does not unlock (engine cannot be started). |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Door Courtesy*7 | Front door courtesy light switch assembly RH / CLOSE or OPEN | CLOSE: Front door RH closed OPEN: Front door RH open | If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part. |
| FL Door Courtesy*8 | Front door courtesy light switch assembly LH / CLOSE or OPEN | CLOSE: Front door LH closed OPEN: Front door LH open | If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part. |