Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER

REAR SUSPENSION MEMBER > REMOVAL

for Preparation Click here



1. REMOVE REAR WHEELS


2. REMOVE CENTER EXHAUST PIPE ASSEMBLY
  1. for 2AR-FE: (Click here)
  2. for 2GR-FE: (Click here)


3. REMOVE NO. 2 FLOOR UNDER COVER


    C240547
  1. Remove the 2 clips.
    Text in Illustration 
    V100135
    Nut (attached to under cover)

  1. Disengage the 6 nuts and remove the No. 2 floor under cover.

    HINT:
    The 6 nuts will remain attached to the No. 2 floor under cover.



4. REMOVE NO. 1 FLOOR UNDER COVER


    C240546
  1. Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.
    Text in Illustration 
    V100135
    Nut (attached to under cover)

    HINT:
    Rotate the clips to disengage them. The 5 nuts and 2 clips will remain attached to the No. 1 floor under cover.



5. SEPARATE REAR STABILIZER LINK ASSEMBLY LH


    C241264
  1. Remove the nut and separate the rear stabilizer link assembly LH from the rear stabilizer bar.
    If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.



6. SEPARATE REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



7. REMOVE REAR STABILIZER BAR


    C240548
  1. Remove the 4 bolts, rear stabilizer bar, 2 rear No. 1 stabilizer bar brackets and 2 rear stabilizer bushings.



8. REMOVE NO. 3 EXHAUST PIPE SUPPORT BRACKET


    C240550
  1. Remove the 2 bolts and No. 3 exhaust pipe support bracket from the rear suspension member sub-assembly.



9. REMOVE REAR BODY END MOUNTING BRACKET SUB-ASSEMBLY


    C240549
  1. Remove the 2 bolts and rear body end mounting bracket sub-assembly from the rear suspension member sub-assembly.



10. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)
(Click here)


11. SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    C144132
  1. Remove the bolt, nut and separate the rear No. 2 suspension arm assembly (outer side) from the rear axle carrier sub-assembly.

    NOTICE:
    When removing the bolt, keep the nut from rotating.



12. SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



13. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    C144131
  1. Remove the bolt, nut and separate the rear No. 1 suspension arm assembly (outer side) from the rear axle carrier sub-assembly.

    NOTICE:
    When removing the bolt, keep the nut from rotating.



14. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



15. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY


    C240551E01
  1. Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.
    Text in Illustration 
    *1
    Engine Lifter
    *2
    Attachment
    V100155
    Attachment Placement Location

    NOTICE:
    1. Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.
    2. Use the attachments to keep the rear suspension member sub-assembly level.



  1. Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stopper sub-assemblies and 2 rear suspension member lower stoppers.


    C240552

  1. Slowly lower the rear suspension member sub-assembly.

    NOTICE:
    When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.



16. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    C241263
  1. Remove the bolt and rear No. 2 suspension arm assembly LH from the rear suspension member sub-assembly.



17. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



18. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    C241262
  1. Remove the bolt and rear No. 1 suspension arm assembly from the rear suspension member sub-assembly.



19. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



20. REMOVE REAR SUSPENSION MEMBER DAMPER (w/ Dynamic Damper)


    C203221
  1. Remove the 2 bolts and rear suspension member damper from the rear suspension member sub-assembly.



21. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH


    C240553E01
  1. Using SST and a press, remove the rear suspension member body mounting front cushion LH from the rear suspension member sub-assembly.

    SST
    09527-17011  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



22. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

HINT:
Perform the same procedure as the LH side.



23. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)


    C240554E01
  1. Using SST and a press, remove the rear suspension member body mounting rear cushion from the rear suspension member sub-assembly.

    SST
    09527-17011  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



24. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

HINT:
Perform the same procedure as the LH side.



25. REMOVE HOLE PLUG


    C240555
  1. Remove the 3 hole plugs from the rear suspension member sub-assembly.

    HINT:
    There are 2 sizes of the hole plugs.