Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK WINDSHIELD WIPER RELAY ASSEMBLY

E125552E16

  1. Disconnect the I72 windshield wiper relay assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I72-2 (IG) - Body ground
    L - Body ground
    Ignition switch ON signal (Power source circuit)
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    I72-8 (VR2) - I72-21 (VR1)
    B - W
    Adjusting volume circuit
    Windshield wiper switch adjusting ring* changed
    0 to 220 Ω
    I72-12 (E) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    I72-16 (WIG) - Body ground
    Y - Body ground
    Signal power source circuit
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    I72-25 (W) - Body ground
    GR - Body ground
    Front washer switch circuit
    Front washer switch on
    Below 1 Ω
    Front washer switch off
    10 kΩ or higher

    HINT:
    *: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.

    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the I72 windshield wiper relay assembly connector.



  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I72-1 (+SM) - Body ground
    B - Body ground
    Front wiper motor position detection signal
    Front wiper motor in low or high operation
    Below 1 V ←→ 11 to 14 V
    Front wiper motor off
    Below 1 V
    I72-3 (C1) - I72-5 (CO)
    P - R
    Front wiper switch AUTO signal circuit
    Ignition switch ON, front wiper switch in AUTO
    Below 1 V
    Ignition switch ON, front wiper switch off
    11 to 14 V
    I72-10 (+1) - Body ground
    B - Body ground
    Front wiper motor low speed signal circuit
    Front wiper motor in low operation
    11 to 14 V
    Front wiper motor off
    Below 1 V
    I72-11 (+2) - Body ground
    V - Body ground
    Front wiper motor high speed signal circuit
    Front wiper motor in high operation
    11 to 14 V
    Front wiper motor off
    Below 1 V
    I72-14 (MPX1) - Body ground
    G - Body ground
    Rain sensor signal
    Ignition switch ON
    Pulse generation
    I72-24 (SPD) - Body ground
    V - Body ground
    Speed signal
    Ignition switch ON, wheel being rotated
    Pulse generation
    (See Waveform 1)
    I72-25 (W) - Body ground
    GR - Body ground
    Front washer switch circuit
    Front washer switch on
    Below 1 V
    Front washer switch off
    11 to 14 V
    If the result is not as specified, the windshield wiper relay assembly may have a malfunction.



      I043789E03
    1. Waveform 1 (Reference):
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


CHECK HEADLIGHT CLEANER CONTROL RELAY (w/ Headlight Cleaner System)

E119074E11

  1. Disconnect the A52 headlight cleaner control relay connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A52-1 (HDLO) - A52-4 (E)
    GR - W-B
    Low beam headlight signal
    Light control switch in head position
    Below 1 V
    Light control switch off
    11 to 14 V
    A52-2 (H) - A52-4 (E)
    SB - W-B
    Headlight cleaner switch operation signal
    Ignition switch ON, light control switch in off position and headlight cleaner switch off
    Below 1 V
    Ignition switch ON, light control switch in off position and headlight cleaner switch on
    11 to 14 V
    A52-3 (IG) - A52-4 (E)
    R - W-B
    Ignition switch ON signal (Power source circuit)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    A52-4 (E) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    A52-5 (FRWA) - A52-4 (E)
    G - W-B
    Front washer switch signal
    Ignition switch ON and front washer switch off
    11 to 14 V
    Ignition switch ON and front washer switch on
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.