Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > Wiper and Washer Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit detects the state of the windshield wiper switch assembly (front wiper switch and front washer switch) and sends it to the windshield wiper relay assembly.

WIRING DIAGRAM


for LHD

E227681E01


for RHD

E227681E02


INSPECTION PROCEDURE

1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY


    E227241E01
  1. for LHD:

    1. Remove the windshield wiper switch assembly (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-3 (+1) - I32-1 (+S)
      OFF
      Below 1 Ω
      I32-3 (+1) - I32-2 (+B)
      MIST
      LO
      I32-2 (+B) - I32-4 (+2)
      HI
      I32-8 (AUTO) - I32-9 (E)
      AUTO
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I31-4 (EW) - I31-7 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Adjusting Ring* 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-7 (VR1) - I32-6 (VR2)
      P1
      209 to 231 Ω
      P2
      114 to 126 Ω
      P3
      58.9 to 65.1 Ω
      P4
      Below 1 Ω

      HINT:
      *: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.

      Text in Illustration 
      *1
      Windshield Wiper Switch Assembly (Adjusting Ring Position)
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)



    E227242E01
  1. for RHD:

    1. Remove the windshield wiper switch assembly (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-2 (+1) - I32-4 (+S)
      OFF
      Below 1 Ω
      I32-2 (+1) - I32-3 (+B)
      MIST
      LO
      I32-3 (+B) - I32-1 (+2)
      HI
      I32-7 (AUTO) - I32-6 (E)
      AUTO
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I31-7 (EW) - I31-4 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Adjusting Ring* 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-9 (VR1) - I32-8 (VR2)
      P1
      209 to 231 Ω
      P2
      114 to 126 Ω
      P3
      58.9 to 65.1 Ω
      P4
      Below 1 Ω

      HINT:
      *: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.

      Text in Illustration 
      *1
      Windshield Wiper Switch Assembly (Adjusting Ring Position)
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY AND BODY GROUND)
  1. for LHD:

    1. Disconnect the I72 windshield wiper relay assembly connector and B1*1 or A29*2 windshield wiper motor assembly connector.

      1. *1: TMC made
      2. *2: TMMR made

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I32-2 (+B) - I72-2 (IG)
      Always
      Below 1 Ω
      I32-2 (+B) - Body ground
      Always
      10 kΩ or higher
      I32-3 (+1) - B1-5 (+1)*1
      Always
      Below 1 Ω
      I32-3 (+1) - A29-5 (+1)*2
      Always
      Below 1 Ω
      I32-3 (+1) - Body ground
      Always
      10 kΩ or higher
      I32-4 (+2) - I72-11 (+2)
      Always
      Below 1 Ω
      I32-4 (+2) - B1-3 (+2)*1
      Always
      Below 1 Ω
      I32-4 (+2) - A29-3 (+2)*2
      Always
      Below 1 Ω
      I32-4 (+2) - Body ground
      Always
      10 kΩ or higher
      I32-1 (+S) - I72-10 (+1)
      Always
      Below 1 Ω
      I32-1 (+S) - Body ground
      Always
      10 kΩ or higher
      I32-8 (AUTO) - I72-3 (C1)
      Always
      Below 1 Ω
      I32-8 (AUTO) - Body ground
      Always
      10 kΩ or higher
      I32-9 (E) - I72-5 (CO)
      Always
      Below 1 Ω
      I32-9 (E) - Body ground
      Always
      10 kΩ or higher
      I32-7 (VR1) - I72-21 (VR1)
      Always
      Below 1 Ω
      I32-7 (VR1) - Body ground
      Always
      10 kΩ or higher
      I32-6 (VR2) - I72-8 (VR2)
      Always
      Below 1 Ω
      I32-6 (VR2) - Body ground
      Always
      10 kΩ or higher
      I31-7 (WF) - I72-25 (W)
      Always
      Below 1 Ω
      I31-7 (WF) - Body ground
      Always
      10 kΩ or higher
      I31-4 (EW) - Body ground
      Always
      Below 1 Ω

      1. *1: TMC made
      2. *2: TMMR made

  1. for RHD:

    1. Disconnect the I72 windshield wiper relay assembly connector and B1 windshield wiper motor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I32-3 (+B) - I72-2 (IG)
      Always
      Below 1 Ω
      I32-3 (+B) - Body ground
      Always
      10 kΩ or higher
      I32-2 (+1) - B1-1 (+1)
      Always
      Below 1 Ω
      I32-2 (+1) - Body ground
      Always
      10 kΩ or higher
      I32-1 (+2) - I72-11 (+2)
      Always
      Below 1 Ω
      I32-1 (+2) - B1-4 (+2)
      Always
      Below 1 Ω
      I32-1 (+2) - Body ground
      Always
      10 kΩ or higher
      I32-4 (+S) - I72-10 (+1)
      Always
      Below 1 Ω
      I32-4 (+S) - Body ground
      Always
      10 kΩ or higher
      I32-7 (AUTO) - I72-3 (C1)
      Always
      Below 1 Ω
      I32-7 (AUTO) - Body ground
      Always
      10 kΩ or higher
      I32-6 (E) - I72-5 (CO)
      Always
      Below 1 Ω
      I32-6 (E) - Body ground
      Always
      10 kΩ or higher
      I32-9 (VR1) - I72-21 (VR1)
      Always
      Below 1 Ω
      I32-9 (VR1) - Body ground
      Always
      10 kΩ or higher
      I32-8 (VR2) - I72-8 (VR2)
      Always
      Below 1 Ω
      I32-8 (VR2) - Body ground
      Always
      10 kΩ or higher
      I31-4 (WF) - I72-25 (W)
      Always
      Below 1 Ω
      I31-4 (WF) - Body ground
      Always
      10 kΩ or higher
      I31-7 (EW) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)