WIPER AND WASHER SYSTEM > Front Wiper Motor Circuit |
| for LHD |

| for RHD |

| 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY |
for LHD:
Remove the windshield wiper motor assembly (Click here).
![]() |
Check low speed operation.
Connect a battery positive (+) lead to terminal B1-5 (+1)*1 or A29-5 (+1)*2 and a negative (-) lead to terminal B1-4 (E)*1 or A29-4 (E)*2, and check that the motor operates at low speed.
Check high speed operation.
Connect a battery positive (+) lead to terminal B1-3 (+2)*1 or A29-3 (+2)*2 and a negative (-) lead to terminal B1-4 (E)*1 or A29-4 (E)*2, and check that the motor operates at high speed.
| *a | Component without harness connected (Windshield Wiper Motor Assembly) |
for RHD:
Remove the windshield wiper motor assembly (Click here).
![]() |
Check low speed operation.
Connect a battery positive (+) lead to terminal B1-1 (+1) and a negative (-) lead to terminal B1-5 (E), and check that the motor operates at low speed.
Check high speed operation.
Connect a battery positive (+) lead to terminal B1-4 (+2) and a negative (-) lead to terminal B1-5 (E), and check that the motor operates at high speed.
| *a | Component without harness connected (Windshield Wiper Motor Assembly) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BATTERY AND BODY GROUND) |
for LHD:
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B1-2 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| A29-2 (B) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-4 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A29-4 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Windshield Wiper Motor Assembly) |
for RHD:
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B1-2 (B) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-5 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Windshield Wiper Motor Assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY) |
for LHD:
Disconnect the I72 windshield wiper relay assembly connector and I32 windshield wiper switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-5 (+1) - I32-3 (+1) | Always | Below 1 Ω |
| B1-5 (+1) - Body ground | Always | 10 kΩ or higher |
| B1-3 (+2) - I72-11 (+2) | Always | Below 1 Ω |
| B1-3 (+2) - I32-4 (+2) | Always | Below 1 Ω |
| B1-3 (+2) - Body ground | Always | 10 kΩ or higher |
| B1-1 (+S) - I72-1 (+SM) | Always | Below 1 Ω |
| B1-1 (+S) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A29-5 (+1) - I32-3 (+1) | Always | Below 1 Ω |
| A29-5 (+1) - Body ground | Always | 10 kΩ or higher |
| A29-3 (+2) - I72-11 (+2) | Always | Below 1 Ω |
| A29-3 (+2) - I32-4 (+2) | Always | Below 1 Ω |
| A29-3 (+2) - Body ground | Always | 10 kΩ or higher |
| A29-1 (+S) - I72-1 (+SM) | Always | Below 1 Ω |
| A29-1 (+S) - Body ground | Always | 10 kΩ or higher |
for RHD:
Disconnect the I72 windshield wiper relay assembly connector and I32 windshield wiper switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-1 (+1) - I32-2 (+1) | Always | Below 1 Ω |
| B1-1 (+1) - Body ground | Always | 10 kΩ or higher |
| B1-4 (+2) - I72-11 (+2) | Always | Below 1 Ω |
| B1-4 (+2) - I32-1 (+2) | Always | Below 1 Ω |
| B1-4 (+2) - Body ground | Always | 10 kΩ or higher |
| B1-3 (+S) - I72-1 (+SM) | Always | Below 1 Ω |
| B1-3 (+S) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||