FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY |
| 1. INSTALL SEAT TRACK ADJUSTING HANDLE |
Engage the 2 springs to install the seat track adjusting handle.
| 2. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY |
Engage the 4 guides to install the separate type front seatback spring assembly.
Install the 4 bolts.
| 3. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side) |
Engage the 3 claws to install the front seat cushion edge protector LH.
Install the screw.
| 4. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side) |
Engage the 3 claws to install the front seat cushion edge protector RH.
Install the screw.
| 5. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side) |
Engage the 3 claws to install the front seat cushion edge protector LH.
Install the screw.
| 6. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side) |
Engage the 3 claws to install the front seat cushion edge protector RH.
Install the screw.
| 7. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Engage the guide to install the reclining adjuster inside cover LH.
| 8. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
Engage the guide to install the reclining adjuster inside cover RH.
| 9. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side) |
![]() |
Engage the clip to install the front seat lower cushion shield LH.
Engage the hook as shown in the illustration.
Install the screw.
| 10. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side) |
![]() |
Engage the clip to install the front seat lower cushion shield RH.
Engage the hook as shown in the illustration.
Install the screw.
| 11. INSTALL SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.
| 12. INSTALL FRONT SEAT AIRBAG ASSEMBLY |
Install the front seat airbag assembly with 2 new nuts.
Engage the 2 clamps.
| 13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD |
Temporarily install the separate type front seatback cover with pad.
Engage the 4 claws to install the 2 front seat headrest supports.
Install the 2 brackets with the nut.
![]() |
Turn back the separate type front seatback cover.
Using hog ring pliers, install the 2 new hog rings.
![]() |
Using hog ring pliers, install 3 new hog rings.
![]() |
Using hog ring pliers, install 5 new hog rings.
| 14. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 16 new hog rings.
![]() |
Using hog ring pliers, install 2 new hog rings.
| 15. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD |
Temporarily install the separate type front seat cushion cover with pad.
Engage each hook.
Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.
Engage the fastener to secure the front seat airbag assembly wire harness.
| 16. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) |
![]() |
Install the front seat inner belt assembly with the nut.
| *1 | Protruding Part |
Engage the clamp.
Engage each clamp under the front seat assembly.
| 17. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) |
![]() |
Install the front seat inner belt assembly with the nut.
| *1 | Protruding Part |
| 18. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side) |
Engage the 5 claws and 6 guides to install the front seat inner cushion shield.
| 19. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side) |
Engage the 5 claws and 7 guides to install the front seat inner cushion shield.
| 20. INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side) |
Engage the 5 claws, 6 guides and clip to install the front seat cushion shield.
Install the screw.
| 21. INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side) |
Engage the 5 claws, 7 guides and clip to install the front seat cushion shield.
Install the screw.
| 22. CONNECT SEPARATE TYPE FRONT SEATBACK COVER |
Connect the rubber band of the separate type front seatback cover.
| 23. INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side) |
Install the vertical adjusting handle with the screw.
| 24. INSTALL RECLINING ADJUSTER RELEASE HANDLE |
Engage the claw to install the reclining adjuster release handle.
| 25. INSTALL SEAT ADJUSTER COVER CAP |
Install the 2 seat adjuster cover caps.