Home › Drivetrain ยท U241E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP

OIL PUMP > DISASSEMBLY

for Preparation Click here



1. INSPECT OIL PUMP ASSEMBLY


    D009205E01
  1. Turn the drive gear using 2 screwdrivers and make sure that it rotates smoothly.

    NOTICE:
    Be careful not to damage the oil seal lip.



2. REMOVE CLUTCH DRUM OIL SEAL RING


    D003650E02
  1. Remove the 2 clutch drum oil seal rings.



3. REMOVE STATOR SHAFT ASSEMBLY


    D003651E01
  1. Using a T30 ''TORX'' socket, remove the 11 bolts and stator shaft.



4. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY


    D009207E02
  1. Push the driven gear to one side of the body. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.10 to 0.17 mm (0.00394 to 0.00669 in.)

    Maximum body clearance:
    0.17 mm (0.00669 in.)

    If the body clearance is greater than the maximum, replace the oil pump body.



    D009208E01
  1. Measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.07 to 0.15 mm (0.00276 to 0.00591 in.)

    Maximum tip clearance:
    0.15 mm (0.00591 in.)

    If the tip clearance is greater than the maximum, replace the oil pump body.



    D009209E01
  1. Using a straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.000787 to 0.00197 in.)

    Maximum side clearance:
    0.05 mm (0.00197 in.)


    Standard Drive Gear Thickness:
    Mark
    Thickness
    1
    10.690 to 10.699 mm (0.42087 to 0.42122 in.)
    2
    10.700 to 10.709 mm (0.42126 to 0.42161 in.)
    3
    10.710 to 10.720 mm (0.42165 to 0.42205 in.)
    4
    10.721 to 10.730 mm (0.42209 to 0.42244 in.)
    5
    10.731 to 10.740 mm (0.42248 to 0.42283 in.)
    Standard Driven Gear Thickness:
    Mark
    Thickness
    1
    10.690 to 10.699 mm (0.42087 to 0.42122 in.)
    2
    10.700 to 10.709 mm (0.42126 to 0.42161 in.)
    3
    10.710 to 10.720 mm (0.42165 to 0.42205 in.)
    4
    10.721 to 10.730 mm (0.42209 to 0.42244 in.)
    5
    10.731 to 10.740 mm (0.42248 to 0.42283 in.)



5. REMOVE FRONT OIL PUMP DRIVE GEAR


    D009206E11
  1. Remove the front oil pump drive gear.



6. REMOVE FRONT OIL PUMP DRIVEN GEAR


    D009206E10
  1. Remove the front oil pump driven gear.



7. REMOVE FRONT OIL PUMP BODY O-RING


    C083490E01
  1. Using a screwdriver, pry out the O-ring.

    HINT:
    Tape the screwdriver before use.



8. REMOVE FRONT OIL PUMP OIL SEAL


    D003647E01
  1. Mount the oil pump in a soft jaw vise.

    NOTICE:
    Be careful not to the damage the oil pump body in the vise.

  1. Using SST, tap out the oil seal from the oil pump body.

    SST
    09308-00010  



9. INSPECT FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY


    D003648E01
  1. Using a caliper gauge, measure the inside diameter of the oil pump body bush.

    Standard inside diameter:
    38.11 to 38.14 mm (1.50039 to 1.50157 in.)

    Maximum inside diameter:
    38.19 mm (1.5035 in.)

    If the inside diameter is greater than the maximum, replace the oil pump body.



10. INSPECT STATOR SHAFT ASSEMBLY


    D003653E01
  1. Using a caliper gauge, measure the inside diameter of the stator shaft bushes.

    Standard inside diameter:
    20.50 to 21.53 mm (0.8071 to 0.8476 in.)

    Maximum inside diameter:
    21.57 mm (0.8492 in.)

    If the inside diameter is greater than the maximum, replace the stator shaft assembly.