Home › Drivetrain ยท U241E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL PINION THRUST WASHER


    C083137E01
  1. Coat the 2 front differential side gears, 2 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF, and install them to the differential case.



2. INSTALL NO. 1 FRONT DIFFERENTIAL PINION SHAFT


    C083135E01
  1. Coat the No. 1 front differential pinion shaft with ATF, and install it to the differential case.



3. INSPECT FRONT DIFFERENTIAL SIDE GEAR BACKLASH


    C083138E01
  1. Using a dial indicator, measure the backlash of the side gear.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

    Standard Thrust Washer Thickness:
    Thickness
    Thickness
    1.0 mm (0.0394 in.)
    1.2 mm (0.0472 in.)
    1.1 mm (0.0433 in.)
    1.3 mm (0.0512 in.)



4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN


    C060005E01
  1. Using a pin punch (5 mm) and hammer, tap in the pinion shaft straight pin.



    C060006E01
  1. Using a chisel and hammer, stake the differential case.



5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    C223436E01
  1. Using SST and a press, press in a new front differential case rear tapered roller bearing to the differential case.

    SST
    09710-30012   (09710-04081)
    09950-60010   (09951-00430, 09951-00580, 09952-06010)
    09950-70010   (09951-07100)



    D025219E02
  1. Using SST and a hammer, tap in the shim and new front differential case tapered roller bearing rear outer race to the transaxle case.

    SST
    09950-60020   (09951-00790)
    09950-70010   (09951-07100)



6. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    C223437E01
  1. Using SST and a press, press in a new front differential case front tapered roller bearing to the differential case.

    SST
    09710-30012   (09710-04081)
    09950-60010   (09951-00430, 09951-00580, 09952-06010)
    09950-70010   (09951-07100)



    D025217E01
  1. Using SST and a hammer, tap in a new front differential case tapered roller bearing front outer race to the transaxle housing.

    SST
    09950-60020   (09951-00750)
    09950-70010   (09951-07100)



7. INSTALL FRONT DIFFERENTIAL RING GEAR


    D025215E03
  1. Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

  1. Clean the contact surface of the front differential case.



    C083132E05
  1. Align the matchmarks, and install the front differential ring gear case quickly.
    Text in Illustration 
    *a
    Matchmark



    C083133E02
  1. Tighten the 10 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



8. INSPECT TAPERED ROLLER BEARING PRELOAD


    C083139E01
  1. Install the differential assembly to the transaxle case.



    C179461E04
  1. Install the transaxle housing to the transaxle with the 18 bolts.

    Torque:
    Bolt A:
    22 N*m{ 225 kgf*cm , 16 ft.*lbf }
    Bolt B:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }
    Bolt C:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }
    Bolt D:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    Bolt E:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    Bolt F:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

    Bolt length:
    Bolt A, B, D, E:
    50 mm (1.969 in.)
    Bolt C, F:
    42 mm (1.654 in.)



    C083572E02
  1. Using SST, turn the differential.

    SST
    09564-50010  



    C083572E02
  1. Using SST and a torque wrench, measure the preload of the differential.

    SST
    09564-50010  

    Torque:
    Standard turning torque at 60 rpm:
    0.20 to 0.69 N*m{ 2.0 to 7.0 kgf*cm , 1.8 to 6.1 in.*lbf } for new
    0.10 to 0.35 N*m{ 1.0 to 3.6 kgf*cm , 0.9 to 3.1 in.*lbf } for used

    Standard Adjusting Shim Thickness:
    Mark
    Thickness
    0
    1.90 mm (0.0748 in.)
    1
    1.95 mm (0.0768 in.)
    2
    2.00 mm (0.0787 in.)
    3
    2.05 mm (0.0807 in.)
    4
    2.10 mm (0.0827 in.)
    5
    2.15 mm (0.0846 in.)
    6
    2.20 mm (0.0866 in.)
    7
    2.25 mm (0.0886 in.)
    8
    2.30 mm (0.0906 in.)
    9
    2.35 mm (0.0925 in.)
    A
    2.40 mm (0.0945 in.)
    B
    2.45 mm (0.0965 in.)
    C
    2.50 mm (0.0984 in.)
    D
    2.55 mm (0.100 in.)
    E
    2.60 mm (0.102 in.)
    F
    2.65 mm (0.104 in.)
    G
    2.70 mm (0.106 in.)
    H
    2.75 mm (0.108 in.)
    J
    2.80 mm (0.110 in.)



    C179461
  1. Remove the 18 bolts.

  1. Using a plastic-faced hammer, remove the transaxle housing.



    C083139E01
  1. Remove the differential.



9. INSTALL TRANSAXLE HOUSING OIL SEAL


    C196088E01
  1. Using SST and a hammer, install a new transaxle housing oil seal.

    SST
    09316-60011   (09316-00011)

    Standard depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Do not damage the oil seal lip.

  1. Coat the lip of the oil seal with MP grease.



10. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL


    C196089E01
  1. Using SST and a hammer, install a new differential side bearing retainer oil seal.

    SST
    09649-17010  
    09950-70010   (09951-07150)

    Standard depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Do not damage the oil seal lip.

  1. Coat the lip of the oil seal with MP grease.