Home › Drivetrain ยท U241E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and speedometer driven hole cover sub-assembly from the transaxle case.

  1. Remove the O-ring from the speedometer driven hole cover sub-assembly.



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C209101
  1. Remove the nut, washer and control shaft lever from the manual valve lever shaft.



    D008033E01
  1. Using a screwdriver, unstake the lock plate and remove the lock nut and lock plate.



    D008034E03
  1. Remove the 2 bolts and pull out the park/neutral position switch assembly.



3. REMOVE BREATHER PLUG HOSE
  1. Remove the breather plug hose from the No. 2 breather plug.



4. REMOVE NO. 1 BREATHER PLUG
  1. Remove the No. 1 breather plug from the breather plug hose.



5. REMOVE NO. 2 BREATHER PLUG
  1. Remove the No. 2 breather plug from the transaxle case.

  1. Remove the O-ring from the No. 2 breather plug.



6. REMOVE OIL COOLER OUTLET TUBE UNION


    C194987
  1. Remove the oil cooler outlet tube union from the transaxle case.

  1. Remove the O-ring from the oil cooler outlet tube union.



7. REMOVE OIL COOLER INLET TUBE UNION


    C194988
  1. Remove the oil cooler inlet tube union from the transaxle case.

  1. Remove the O-ring from the oil cooler inlet tube union.



8. REMOVE SPEED SENSOR


    D030672E11
  1. Remove the speed sensor NT.
    Text in Illustration 
    *1
    Speed Sensor NC
    *2
    Speed Sensor NT

    1. Remove the bolt and speed sensor NT from the transaxle case.

      NOTICE:
      Two different types of bolt may be used to secure the sensor. If a precoated bolt has been used, replace it with a new one.

    2. Remove the O-ring from the speed sensor NT.

  1. Remove the speed sensor NC.

    1. Remove the bolt and speed sensor NC from the transaxle case.

    2. Remove the O-ring from the speed sensor NC.



9. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C134835
  1. Remove the 4 No. 1 transaxle case plugs from the transaxle case.

  1. Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.



    C248871
  1. Remove the 2 No. 1 transaxle case plugs from the transaxle housing.

  1. Remove the 2 O-rings from the No. 1 transaxle case plugs.



10. SECURE AUTOMATIC TRANSAXLE ASSEMBLY


    D009176E01
  1. Place the automatic transaxle assembly on wooden blocks.



11. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    D009177E01
  1. Remove the 18 bolts and automatic transaxle oil pan sub-assembly from the transaxle case.



    C209099E03
  1. Remove the 2 magnets from the automatic transaxle oil pan sub-assembly.

  1. Remove the gasket from the automatic transaxle oil pan sub-assembly.
    Text in Illustration 
    *1
    Magnet



12. INSPECT AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    AT00103E01
  1. Remove the magnets and use them to collect any steel chips. Examine the chips and particles in the pan and on the magnets to determine what type of wear has occurred in the transaxle.
    Steel (magnetic): bearing, gear and plate wear
    Brass (non-magnetic): bush wear



13. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    D009179E01
  1. Remove the 3 bolts and valve body oil strainer assembly from the transaxle case.



    D009180E01
  1. Remove the O-ring from the valve body oil strainer assembly.



14. REMOVE TRANSMISSION WIRE


    C130917E06
  1. Remove the 5 connectors from the shift solenoid valves.

  1. Remove the bolt, lock plate and ATF temperature sensor from the transaxle case.
    Text in Illustration 
    *1
    Lock Plate



    D003547E08
  1. Remove the bolt and transmission wire from the transaxle case.



    D003636E03
  1. Remove the O-ring from the transmission wire.



15. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    D003553E05
  1. Support the transmission valve body assembly and remove the 17 bolts and the transmission valve body assembly from the transaxle case.

    NOTICE:
    Do not drop the check ball body, spring or accumulator piston.



16. REMOVE NO. 1 GOVERNOR APPLY GASKET


    C083127E01
  1. Remove the No. 1 governor apply gasket from the transaxle case.



17. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


    C083128E01
  1. Remove the transaxle case 2nd brake gasket from the transaxle case.



18. REMOVE BRAKE DRUM GASKET


    C083129E01
  1. Remove the brake drum gasket from the transaxle case.



19. REMOVE CHECK BALL BODY


    D003554E02
  1. Remove the check ball body and spring from the transaxle case.



20. REMOVE C-3 ACCUMULATOR PISTON


    D003555E01
  1. Remove the spring from the C-3 accumulator piston.



    D003556E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF when applying compressed air.



    D003902E02
  1. Remove the O-ring from the C-3 accumulator piston.



21. REMOVE C-1 ACCUMULATOR PISTON


    D003557E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-1 accumulator piston and spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF when applying compressed air.



    D003903E01
  1. Remove the 2 O-rings from the C-1 accumulator piston.



22. REMOVE B-3 ACCUMULATOR PISTON


    D003558E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF when applying compressed air.



    D003904E05
  1. Remove the O-ring from the B-3 accumulator piston.



23. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    D003560E03
  1. Remove the 2 bolts, manual detent spring sub-assembly and spring cover.



24. REMOVE PARKING LOCK PAWL BRACKET


    C056727E01
  1. Remove the 2 bolts and parking lock pawl bracket.



25. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


    D003559E01
  1. Using needle-nose pliers, remove the manual valve lever shaft retainer spring.



26. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    D003563E01
  1. Using a chisel and hammer, unstake and remove the spacer.



    D003564E01
  1. Using a pin punch (3 mm) and hammer, tap out the pin.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle.



    D003565E02
  1. Remove the manual valve lever shaft and manual valve lever sub-assembly.



27. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    D003905E01
  1. Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.



28. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    D003566E02
  1. Using a screwdriver, pry out the manual valve lever shaft oil seal from the transaxle case.



29. INSPECT INPUT SHAFT END PLAY
  1. Secure the transaxle case with the oil pump side facing up.



    D008046E01
  1. Using a dial indicator, measure the input shaft end play.

    Standard end play:
    0.262 to 1.25 mm (0.0103 to 0.0492 in.)

    If the end play is not as specified, replace the stator shaft thrust needle roller bearing and the forward clutch hub thrust needle roller bearing.



30. REMOVE TRANSAXLE HOUSING


    C179461
  1. Remove the 18 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic-faced hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential may be accidentally removed when the transaxle housing is removed.



31. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING


    D003606E02
  1. Using SST, remove the underdrive cylindrical roller bearing from the transaxle housing.

    SST
    09514-35011  



32. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING


    D003915E07
  1. Remove the underdrive output shaft oil seal ring from the transaxle housing.



33. REMOVE OIL PUMP ASSEMBLY


    D003569E03
  1. Remove the 7 bolts and oil pump assembly from the transaxle case.



34. REMOVE THRUST NEEDLE ROLLER BEARING


    D025505E03
  1. Remove the thrust needle roller bearing from the underdrive planetary gear assembly.



35. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE


    D025506E04
  1. Remove the No. 2 thrust bearing underdrive race from the underdrive planetary gear assembly.



36. REMOVE FRONT DIFFERENTIAL ASSEMBLY


    D003577E01
  1. Remove the front differential assembly from the transaxle case.



37. REMOVE O-RING


    C273783
  1. Remove the 2 O-rings from the transaxle case.



38. REMOVE FORWARD CLUTCH ASSEMBLY


    D003574E03
  1. Remove the forward clutch assembly from the transaxle case.



    D003906E02
  1. Remove the thrust bearing from the forward clutch assembly.



39. INSPECT PACK CLEARANCE OF FORWARD CLUTCH


    C194996
  1. Install the forward clutch on the oil pump.

    NOTICE:
    Be careful not to damage the oil seal ring of the oil pump.

  1. Using a dial indicator, measure the forward clutch piston stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Standard piston stroke:
    1.41 to 1.75 mm (0.0555 to 0.0688 in.)

    If the piston stroke is less than the minimum, the parts may have been assembled incorrectly. Check and reassemble again.
    If the clearance is not as specified, select another flange.

    HINT:
    There are 7 different thicknesses of flanges.

    Standard Flange Thickness:
    Mark
    Thickness
    Mark
    Thickness
    0
    2.85 mm (0.112 in.)
    4
    3.45 mm (0.1358 in.)
    1
    3.00 mm (0.1181 in.)
    5
    3.60 mm (0.1417 in.)
    2
    3.15 mm (0.1240 in.)
    6
    3.75 mm (0.147 in.)
    3
    3.30 mm (0.1299 in.)
    -
    -



40. REMOVE FORWARD CLUTCH FLANGE HOLE SNAP RING


    D003660E01
  1. Using a screwdriver, remove the forward clutch flange hole snap ring.



    C194995
  1. Remove the flange, 4 forward multiple disc clutch discs and 4 plates.



41. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC


    D004080E01
  1. Check if the sliding surface of the forward multiple disc clutch disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the forward multiple disc clutch disc is peeling off or discolored, replace all forward multiple disc clutch discs.
    2. Before assembling new forward multiple disc clutch discs, soak them in ATF for at least 15 minutes.



42. REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    D003662E01
  1. Place SST on the spring retainer and compress the forward clutch return spring sub-assembly with a press.

    SST
    09350-32014   (09351-32070)

  1. Using a snap ring expander, remove the snap ring.



    D003663E01
  1. Remove the forward clutch return spring sub-assembly.



43. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    C067855E01
  1. Using a vernier caliper, measure the free length of the forward clutch return spring sub-assembly together with the spring seat.

    Standard free length:
    28.23 mm (1.1114 in.)

    If the result is not as specified, replace the forward clutch return spring sub-assembly.



44. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY


    D003664E01
  1. Place the forward clutch drum onto the oil pump.

  1. Holding the forward clutch piston sub-assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump to remove the forward clutch piston sub-assembly.

    HINT:
    When the piston is slanted and cannot be removed, remove it by pushing down the protruding side and applying compressed air again, or using needle nose pliers with its tips wrapped in tape.



45. REMOVE FORWARD CLUTCH PISTON O-RING


    D009213E01
  1. Remove the 2 forward clutch piston O-rings from the forward clutch piston sub-assembly.



46. INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY


    D003667E01
  1. Shake the forward clutch piston sub-assembly to check that the check ball is not stuck.



    D003668E01
  1. Check that the valve does not leak when applying low pressure compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).



47. REMOVE INPUT SHAFT OIL SEAL RING


    C056374E01
  1. Remove the input shaft oil seal ring from the forward clutch drum.



48. REMOVE MULTIPLE DISC CLUTCH HUB


    D003575E01
  1. Remove the thrust bearing, multiple disc clutch hub, thrust needle roller bearing and bearing race from the transaxle case.



49. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


    D003576E03
  1. Remove the bolt and parking lock pawl shaft clamp from the transaxle case.



    D009201E01
  1. Remove the parking lock pawl shaft from the transaxle case.



    D008048E01
  1. Push the parking lock pawl.

    HINT:
    Failure to do so will cause interference when the underdrive planetary gear assembly is removed.



    D003579E04
  1. Remove the underdrive planetary gear assembly from the transaxle case.

    NOTICE:
    Be careful so that the underdrive planetary gear assembly will not fall out.



    D008049E01
  1. Remove the tension spring, parking lock pawl pin and parking lock pawl from the transaxle case.



50. REMOVE FRONT PLANETARY GEAR NUT


    C134894E03
  1. Using SST, secure the underdrive planetary gear assembly.

    SST
    09387-00050  
    09495-65040  
    Text in Illustration 
    *1
    Underdrive Planetary Gear Assembly



    D003686E01
  1. Using SST and a hammer, loosen the staked part of the front planetary gear nut.

    SST
    09930-00010   (09931-00010, 09931-00020)



    C134896E03
  1. Clamp the underdrive planetary gear assembly in a soft jaw vise.

    NOTICE:
    Be careful not to damage the differential drive pinion.

    Text in Illustration 
    *1
    Underdrive Planetary Gear Assembly



    C134897E04
  1. Using a socket wrench, remove the front planetary gear nut.
    Text in Illustration 
    *1
    Underdrive Planetary Gear Assembly



51. REMOVE CYLINDRICAL ROLLER BEARING INNER RACE


    D003689E09
  1. Using SST, remove the cylindrical roller bearing inner race.

    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00320)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



52. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C134898E01
  1. Using SST and a press, remove the differential drive pinion, parking lock gear, counter driven gear with underdrive planetary ring gear, and underdrive angular ball bearing (front side).

    SST
    09387-00050  
    09495-65040  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



    C134899E04
  1. Clamp the underdrive planetary gear assembly in a soft jaw vise.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Be careful not to damage the underdrive planetary gear assembly.

  1. Using SST, remove the underdrive angular ball bearing (rear side) from the underdrive planetary gear assembly.

    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00320)



53. REMOVE UNDERDRIVE PLANETARY RING GEAR


    C134900E04
  1. Using snap ring pliers, remove the underdrive planetary ring hole snap ring.
    Text in Illustration 
    *1
    Underdrive Planetary Ring Hole Snap Ring



    C137499E04
  1. Remove the underdrive planetary ring gear from the counter driven gear.
    Text in Illustration 
    *1
    Underdrive Planetary Ring Gear
    *2
    Counter Driven Gear



54. REMOVE UNDERDRIVE CLUTCH ASSEMBLY


    D003580E02
  1. Remove the underdrive clutch assembly, needle roller bearing and No. 3 thrust bearing underdrive race from the transaxle case.



55. INSPECT UNDERDRIVE CLUTCH PAC CLEARANCE
  1. Install the underdrive clutch to the transaxle case.

    NOTICE:
    Be careful not to damage the oil seal rings.



    D008123E01
  1. Install a dial indicator as shown in the illustration.



    D008124E01
  1. Measure the underdrive clutch piston stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Standard pack clearance:
    1.51 to 1.71 mm (0.0594 to 0.0673 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.
    If the pack clearance is less than the minimum, the parts may have been assembled incorrectly, so check and reassemble again.
    If the pack clearance is not as specified, select another flange.

    HINT:
    There are 7 flanges in different thickness.

    Standard Flange Thickness:
    Mark
    Thickness
    Mark
    Thickness
    A
    3.0 mm (0.118 in.)
    G
    3.1 mm (0.122 in.)
    B
    3.2 mm (0.126 in.)
    H
    3.3 mm (0.130 in.)
    C
    3.4 mm (0.134 in.)
    J
    3.5 mm (0.138 in.)
    F
    2.9 mm (0.114 in.)
    -
    -



56. REMOVE NO. 1 UNDERDRIVE CLUTCH DISC SNAP RING


    D008125E01
  1. Using a screwdriver, pry out the No. 1 underdrive clutch disc snap ring from the underdrive clutch drum sub-assembly.

    HINT:
    Tape the screwdriver before use.



    C129394
  1. Remove the flange, 3 discs and 3 plates from the underdrive clutch drum sub-assembly.



57. INSPECT NO. 1 UNDERDRIVE CLUTCH DISC


    D004077E01
  1. Check to see if the sliding surface of the No. 1 underdrive clutch disc, plate and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    1. If the lining of the No. 1 underdrive clutch disc is peeling off or discolored, replace all No. 1 underdrive clutch discs.
    2. Before assembling new No. 1 underdrive clutch discs, soak them in ATF for at least 15 minutes.



58. REMOVE UNDERDRIVE CLUTCH PISTON SET


    D003703E02
  1. Place SST on the clutch balancer and compress the spring with a press.

    SST
    09350-32014   (09351-32070)

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop pressing when the spring seat is 1 to 2 mm (0.0394 to 0.0787 in.) below the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.



    D003704E01
  1. Remove the clutch balancer and underdrive clutch return spring sub-assembly from the underdrive clutch drum sub-assembly.



    D008127E01
  1. Install the underdrive clutch assembly to the transaxle case.

    NOTICE:
    Be careful not to damage the oil seal rings.



    D008128E01
  1. Holding the underdrive clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive clutch piston.



59. INSPECT UNDERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY


    D009214E01
  1. Using a vernier caliper, measure the free length of the underdrive clutch return spring sub-assembly together with the spring seat.

    Standard free length:
    17.14 mm (0.6748 in.)

    If the result is not as specified, replace the underdrive clutch return spring sub-assembly.



60. REMOVE UNDERDRIVE CLUTCH DRUM O-RING


    D004078E01
  1. Using a screwdriver, remove the underdrive clutch drum O-ring from the underdrive clutch drum sub-assembly.



61. INSPECT UNDERDRIVE CLUTCH DRUM SUB-ASSEMBLY


    D008129E02
  1. Using a caliper gauge, measure the inside diameter of the underdrive clutch drum bush.

    Standard drum bushing:
    32.56 to 32.58 mm (1.2818 to 1.2826 in.)

    Maximum drum bushing:
    32.63 mm (1.2846 in.)

    If the inside diameter is greater than the maximum, replace the underdrive clutch drum sub-assembly.



62. REMOVE UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY


    D003581E02
  1. Using a screwdriver, pry out the snap ring from the transaxle case.



    D003627E03
  1. Remove the underdrive one-way clutch assembly from the transaxle case.



    D009198E01
  1. Remove the outer race retainer from the underdrive one-way clutch assembly.



63. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC


    D008050E01
  1. Using a screwdriver, pry out the snap ring from the transaxle case.



    C223612
  1. Remove the flange, 3 No. 2 underdrive clutch discs and 3 plates from the transaxle case.



64. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC


    D009196E01
  1. Check if the sliding surface of the No. 2 underdrive clutch disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the No. 2 underdrive clutch disc is peeling off or discolored, or even if a part of the groove is defaced, replace all No. 2 underdrive clutch discs.
    2. Before assembling new No. 2 underdrive clutch discs, soak them in ATF for at least 15 minutes.



65. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003610E01
  1. Using SST, a snap ring expander and press, remove the snap ring from the transaxle case.

    SST
    09387-00020  



    D008051E01
  1. Remove the underdrive brake return spring sub-assembly from the underdrive brake piston.



66. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003806E01
  1. Using a vernier caliper, measure the free length of the underdrive brake return spring sub-assembly together with the spring seat.

    Standard free length:
    14.04 mm (0.553 in.)

    If the free length is shorter than the standard free length, replace the underdrive brake return spring sub-assembly.



67. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING


    D003914E04
  1. Remove the 2 underdrive clutch drum oil seal rings from the transaxle case.



68. REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY


    C248896
  1. Remove the 11 bolts.

  1. Tap the circumference of the rear transaxle cover sub-assembly with a plastic-faced hammer to remove the rear transaxle cover sub-assembly from the transaxle case.



    D009184E01
  1. Remove the 2 outer rear clutch oil seal rings from the rear transaxle cover sub-assembly.



    C083140E01
  1. Using a T30 ''TORX'' socket wrench, remove the 2 screws and plate.



    D003801E01
  1. Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.

    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01041)



69. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C248895
  1. Remove the 2 No. 1 transaxle case plugs from the rear transaxle cover sub-assembly.

  1. Remove the 2 O-rings from the 2 No. 1 transaxle case plugs.



70. REMOVE UNDERDRIVE BRAKE PISTON


    D003799E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.



    D003794E02
  1. Remove the 2 O-rings from the underdrive brake piston.



    D003605E02
  1. Using SST, remove the needle roller bearing from the transaxle case.

    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01041)



71. REMOVE BRAKE APPLY TUBE


    D025510E02
  1. Remove the bolt, apply pump clamp and brake apply tube from the transaxle case.

  1. Remove the brake apply tube from the apply pump clamp.



72. REMOVE FRONT CLUTCH APPLY TUBE
  1. Remove the front clutch apply tube from the transaxle case.



73. REMOVE O-RING


    D003591E01
  1. Using a screwdriver, remove the 2 O-rings from the transaxle case.

    HINT:
    Tape the screwdriver before use.



74. REMOVE DIRECT CLUTCH ASSEMBLY


    D003586E01
  1. Remove the thrust needle roller bearing and direct clutch assembly from the transaxle case.



    D008053E01
  1. Remove the bearing race from the direct clutch assembly.



75. INSPECT PACK CLEARANCE OF DIRECT CLUTCH


    D009210E01
  1. Install the direct clutch and needle roller bearing on the transaxle rear cover.

  1. Using a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Standard pack clearance:
    0.652 to 0.872 mm (0.0257 to 0.0343 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.
    If the pack clearance is less than the minimum, the parts may have been assembled incorrectly. Check and reassemble them again.
    If the pack clearance is still not as specified, select another flange.

    HINT:
    There are 8 different thicknesses of flanges.

    Standard Flange Thickness:
    Mark
    Thickness
    Mark
    Thickness
    0
    2.9 mm (0.114 in.)
    4
    3.3 mm (0.130 in.)
    1
    3.0 mm (0.118 in.)
    5
    3.4 mm (0.134 in.)
    2
    3.1 mm (0.122 in.)
    6
    3.5 mm (0.138 in.)
    3
    3.2 mm (0.126 in.)
    7
    3.6 mm (0.142 in.)



76. REMOVE DIRECT MULTIPLE DISC CLUTCH DISC SNAP RING


    D008099E01
  1. Using a screwdriver, pry out the direct multiple disc clutch disc snap ring from the direct clutch drum.

    HINT:
    Tape the screwdriver before use.



    C129393
  1. Remove the flange, 3 discs and 3 plates from the direct clutch drum.



77. INSPECT DIRECT MULTIPLE DISC CLUTCH DISC


    D004079E01
  1. Check if the sliding surface of the direct multiple disc clutch disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the direct multiple disc clutch disc is peeling off or discolored, replace all direct multiple disc clutch discs.
    2. Before assembling new direct multiple disc clutch discs, soak them in ATF for at least 15 minutes.



78. REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    D003677E02
  1. Place SST on the clutch balancer and compress the spring with a press.

    SST
    09387-00020  

  1. Using a snap ring expander, remove the snap ring from the direct clutch drum.

    NOTICE:
    1. Stop pressing when the spring seat is 1 to 2 mm (0.0394 to 0.0787 in.) below the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.



    D008101E01
  1. Remove the clutch balancer from the direct clutch drum.



    D008102E01
  1. Remove the direct clutch return spring sub-assembly from the direct clutch drum.



    D008103E01
  1. Install the direct clutch drum on the rear transaxle cover sub-assembly.

  1. Holding the direct clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the rear transaxle cover sub-assembly to remove the direct clutch piston.



79. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    D009211E03
  1. Using a vernier caliper, measure the free length of the direct clutch return spring sub-assembly together with the spring seat.

    Standard free length:
    22.58 mm (0.8890 in.)

    If the result is not as specified, replace the direct clutch return spring sub-assembly.



80. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    D003587E01
  1. Remove the rear planetary sun gear assembly from the transaxle case.



    D003791E01
  1. Remove the thrust bearing from the rear planetary sun gear assembly.



    D008054E01
  1. Remove the No. 1 thrust washer and one-way clutch thrust bearing from the rear planetary sun gear assembly.



81. REMOVE ONE-WAY CLUTCH ASSEMBLY


    C248865E01
  1. Remove the one-way clutch assembly and No. 2 thrust washer from the rear planetary gear assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    No. 2 Thrust Washer



    D003909E02
  1. Remove the one-way clutch inner race from the one-way clutch assembly.



82. REMOVE OUTER ONE-WAY CLUTCH SLEEVE


    D003589E03
  1. Remove the outer one-way clutch sleeve from the transaxle case.



83. REMOVE 2ND BRAKE CLUTCH DISC
  1. Using a screwdriver, remove the snap ring from the transaxle case.



    C129388
  1. Remove the flange, 3 2nd brake clutch discs and 3 plates from the transaxle case.



84. INSPECT 2ND BRAKE CLUTCH DISC


    D004083E01
  1. Check if the sliding surface of the 2nd brake clutch disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the 2nd brake clutch disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all 2nd brake clutch discs.
    2. Before assembling new 2nd brake clutch discs, soak them in ATF for at least 15 minutes.



85. REMOVE 2ND BRAKE PISTON ASSEMBLY


    D008058E03
  1. Using a screwdriver, pry out the snap ring from the transaxle case.



    D008059E01
  1. Remove the 2nd brake piston assembly from the transaxle case.



86. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D003796E04
  1. Place SST on the 2nd brake piston return spring sub-assembly and compress the spring.

    SST
    09387-00060  

  1. Using a screwdriver, pry out the snap ring.



    C083462E01
  1. Remove the 2nd brake piston return spring sub-assembly from the 2nd brake piston.



87. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D003824E02
  1. Using a vernier caliper, measure the free length of the 2nd brake piston return spring sub-assembly together with the spring seat.

    Standard free length:
    16.61 mm (0.6539 in.)

    If the result is not as specified, replace the 2nd brake piston return spring sub-assembly.



88. REMOVE 2ND BRAKE PISTON


    C083463E01
  1. Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.



89. REMOVE 2ND BRAKE PISTON O-RING


    C083465E01
  1. Remove the 2 2nd brake piston O-rings from the 2nd brake piston.



90. REMOVE 1ST AND REVERSE BRAKE CLUTCH DISC


    D009941E01
  1. Remove the flange, 5 1st and reverse brake clutch discs and 5 plates from the transaxle case.



91. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC


    D009189E01
  1. Check if the sliding surface of the 1st and reverse brake clutch disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the 1st and reverse brake clutch disc is peeling off or discolored, or even if a part of the groove is defaced, replace all 1st and reverse brake clutch discs.
    2. Before assembling new 1st and reverse brake clutch discs, soak them in ATF for at least 15 minutes.



92. REMOVE REAR PLANETARY GEAR ASSEMBLY


    D003616E02
  1. Using a screwdriver, pry out the snap ring from the 2nd brake hub.



    D008062E01
  1. Remove the rear planetary gear assembly from the transaxle case.



    D003910E01
  1. Remove the thrust washer from the rear planetary gear assembly.



    D003593E01
  1. Remove the No. 3 thrust bearing race from the rear planetary gear assembly.



93. REMOVE INPUT SUN GEAR


    D003873E03
  1. Remove the 2 thrust bearings, bearing race and input sun gear from the front planetary gear assembly.



94. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    D003595E02
  1. Using a chisel and hammer, unstake the lock washer.

    NOTICE:
    Push down all claws of the washer. Otherwise SST cannot be fully pressed against the nut and cannot loosen the nut.



    D003596E01
  1. Using SST, remove the lock nut.

    SST
    09387-00030  
    09387-00080  

  1. Remove the lock washer.



    D003597E01
  1. Using SST and a press, remove the front planetary gear assembly and 2nd brake hub from the counter drive gear.

    SST
    09950-60010   (09951-00450)



    D008063E01
  1. Remove the front planetary gear assembly from the 2nd brake hub.



95. REMOVE FRONT PLANETARY RING GEAR


    D003615E03
  1. Using a screwdriver, pry out the brake hub snap ring and front planetary ring gear from the 2nd brake hub.



96. REMOVE 1ST AND REVERSE BRAKE PISTON


    D003600E01
  1. Using SST, a press and ring expander, remove the snap ring.

    SST
    09387-00070  

    NOTICE:
    1. Stop pressing when the spring seat is 1 to 2 mm (0.0394 to 0.0787 in.) below the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.



    D008061E01
  1. Remove the 1st and reverse brake return spring from the 1st and reverse brake piston.



    D003800E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF when applying compressed air.



    D003913E01
  1. Remove the 2 O-rings from the 1st and reverse brake piston.



97. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003811E01
  1. Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly together with the spring seat.

    Standard free length:
    15.53 mm (0.611 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.



98. REMOVE COUNTER DRIVE GEAR


    C134861E02
  1. Using SST and a press, remove the counter drive gear from the transaxle case.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)



    D003602E01
  1. Tighten 2 service bolts evenly and make a clearance of approximately 5.0 mm (0.197 in.) between the counter drive gear and the counter drive gear angular ball bearing inner race (front side).



    C134858E03
  1. Using SST, remove the counter drive gear angular ball bearing inner race (front side).

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00590)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



99. REMOVE COUNTER DRIVE GEAR ANGULAR BALL BEARING


    C134859E03
  1. Remove the counter drive gear angular ball bearing inner race (rear side) and counter drive gear angular ball bearing (rear side).
    Text in Illustration 
    *1
    Counter Drive Gear Angular Ball Bearing Inner Race
    *2
    Counter Drive Gear Angular Ball Bearing



    C134860E01
  1. Using SST, remove the counter drive gear angular ball bearing outer race (rear side) from the transaxle case.

    SST
    09308-00010  



    C134925
  1. Remove the counter drive gear angular ball bearing outer race (front side).



    C134862E01
  1. Using SST and a press, remove the counter drive gear angular ball bearing outer race (front side) from the transaxle case.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07200)



    C134863
  1. Using a screwdriver, remove the snap ring from the transaxle case.



100. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    D003607E01
  1. Remove the bolt, No. 2 transaxle apply tube clamp and differential gear lube apply tube from the transaxle housing.