Home › Engine / Hybrid System ยท 2GR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE ENGINE HANGERS


    A129635E18
  1. Remove the 4 bolts and 2 engine hangers.
    Text in Illustration 
    *1
    No. 1 engine hanger
    *2
    No. 2 engine hanger
    *a
    Bank 1
    *b
    Bank 2



2. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    A255337E01
  1. Disconnect the ventilation hose.
    Text in Illustration 
    *A
    Type A
    *B
    Type B

  1. Disconnect the hose clamp and union to check valve hose.



    A255505
  1. Disconnect the connector and wire harness clamp.

  1. Disconnect the 2 water by-pass hoses and fuel vapor feed hose.



    A129467
  1. Disconnect the connector from the intake air control valve assembly.



    A255338
  1. Remove the bolt and vacuum hose clamp.



    A255339
  1. Remove the bolt and separate the throttle body bracket from the intake air surge tank assembly.



    A255340
  1. Remove the bolt and separate the No. 1 surge tank stay from the intake air surge tank assembly.



    A255341
  1. Remove the 2 nuts from the intake air surge tank assembly.

  1. Using a 5 mm socket hexagon wrench, remove the 4 bolts.



    A255342
  1. Remove the intake air surge tank assembly and 3 gaskets.



3. REMOVE NO. 1 SURGE TANK STAY


    A206488
  1. Remove the bolt and No. 1 surge tank stay.



4. REMOVE THROTTLE BODY BRACKET


    A254363
  1. Remove the bolt and throttle body bracket.



5. REMOVE IGNITION COIL ASSEMBLY


    A255007
  1. Remove the nut.

  1. Disconnect the 2 harness clamps.



    A192461
  1. Disconnect the 6 ignition coil connectors.



    A136825
  1. Remove the 6 bolts and 6 ignition coils.



6. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A162388
  1. Remove the bolt and No. 2 engine mounting stay RH.



7. REMOVE INTAKE MANIFOLD


    A134933
  1. Uniformly loosen and remove the 6 bolts and 4 nuts.

  1. Remove the intake manifold and 2 gaskets.



8. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A129637
  1. Uniformly loosen and remove the 6 nuts.

  1. Remove the exhaust manifold sub-assembly RH and gasket.



9. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE


    A202567
  1. Remove the oil level dipstick.

  1. Remove the bolt and No. 2 engine oil level dipstick guide.



    A254364
  1. Remove the O-ring from the No. 2 engine oil level dipstick guide.



10. REMOVE NO. 2 MANIFOLD STAY


    A140783
  1. Remove the bolt, nut and No. 2 manifold stay.



11. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A197636
  1. Remove the 3 bolts and No. 2 exhaust manifold heat insulator.



12. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A207618
  1. Uniformly loosen and remove the 6 nuts.

  1. Remove the exhaust manifold assembly LH and gasket.



13. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A129644
  1. Remove the 5 bolts and V-ribbed belt tensioner assembly.



14. REMOVE NO. 2 TIMING GEAR COVER


    A206492
  1. Remove the 2 bolts and No. 2 timing gear cover.



15. REMOVE WATER PUMP PULLEY


    A226686E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 4 bolts and water pump pulley.



16. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A206493
  1. Remove the bolt, No. 2 idler pulley cover plate, No. 2 idler pulley sub-assembly and idler pulley cover plate.



17. REMOVE NO. 1 VACUUM SWITCHING VALVE


    A206494
  1. Remove the bolt and No. 1 vacuum switching valve.



18. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A129647
  1. Using a deep socket wrench, remove the engine oil pressure switch assembly.



19. REMOVE KNOCK CONTROL SENSOR


    A129615
  1. Disconnect the 2 knock control sensor connectors.

  1. Remove the 2 bolts and 2 knock control sensors.



20. REMOVE KNOCK SENSOR WIRE


    A254366
  1. Disconnect the 3 clamps and remove the knock sensor wire from the engine assembly.



21. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


    A129648
  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.