DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 | Abnormal voltage output:
|
|
| P0137 P0157 | Low voltage (open):
|
|
| P0138 P0158 | High voltage (short):
|
|
| Active Air fuel Ratio Control |
| Abnormal Voltage Output of Heated Oxygen Sensor (DTCs P0136 and P0156) |

| Open or Short in Heated Oxygen Sensor Circuit (DTCs P0137 and P0157 or P0138 and P0158) |

| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Mass air flow meter sub-assembly Throttle position sensor Air fuel ratio sensor |
| Frequency of Operation | Once per driving cycle |
| Active air fuel ratio control | Executing |
| Active air fuel ratio control begins when all of the following conditions are met | - |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Idling | Off |
| Engine speed | Less than 3200 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 70% |
| Either of the following conditions is met | 1 or 2 |
| 1. Both of the following conditions are met | - |
| Commanded air fuel ratio | 14.3 or less |
| Heated oxygen sensor voltage | 0.21 V or higher, and less than 0.59 V |
| 2. Both of the following conditions are met | - |
| Commanded air fuel ratio | 14.9 or more |
| Heated oxygen sensor voltage | 0.21 V or higher, and less than 0.59 V |
| Both of the following conditions are met | - |
| Commanded air fuel ratio | 14.3 or less |
| Heated oxygen sensor voltage | Less than 0.21 V |
| Both of the following conditions are met | - |
| Commanded air fuel ratio | 14.9 or more |
| Heated oxygen sensor voltage | Higher than 0.59 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 AFS Voltage B2S1 (Air fuel ratio) | +12% | Rich | Below 3.1 V |
| -12% | Lean | Higher than 3.4 V | |
| O2S B1S2 O2S B2S2 (Heated oxygen) | +12% | Rich | Higher than 0.55 V |
| -12% | Lean | Below 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0156, P0157 OR P0158) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0138 or P0158 is output | A |
| DTC P0137 or P0157 is output | B |
| DTC P0136 or P0156 is output | C |
| DTC P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / O2S B1S2 or O2S B2S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Heated Oxygen Sensor Output Voltage | Proceed to |
| 1.0 V or higher | A |
| Less than 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
Disconnect the heated oxygen sensor connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX2B) | Always | 10 kΩ or higher |
| *1 | Bank 1 | *2 | Bank 2 |
| *a | Component without harness connected (Heated Oxygen Sensor) | - | - |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the engine switch to off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-28 (HT1B) - E26-101 (OX1B) | Always | 10 kΩ or higher |
| E26-22 (HT2B) - E26-133 (OX2B) | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 AFS Voltage B2S1 (Air fuel ratio) | Alternates between higher and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |

|
| ||||
| OK | |
| 6.INSPECT AIR FUEL RATIO SENSOR |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle by the driving pattern as listed below:
Warm up the engine until the engine coolant temperature reaches 75°C (167°F) or higher.
Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.
Stop the vehicle.
Accelerate the vehicle to 60 km/h (37 mph) or more and decelerate for 5 seconds or more. Perform this 3 times.

Enter the following menus: Powertrain / Engine / Data List / All Data / AFS Current B1S1 and AFS Current B2S1.
Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.
|
| ||||
|
| ||||
| 7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / All Data / O2S B1S2 or O2S B2S2.
Change the fuel injection volume using the tester, monitoring the voltage output of the heated oxygen sensors displayed on the tester.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Change the fuel injection volume using the tester, and monitor the voltage output of air fuel ratio and heated oxygen sensors displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 AFS Voltage B2S1 (Air fuel ratio) | Alternates between higher and less than 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 9.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E22-1 (HT1B) - E26-28 (HT1B) | Always | Below 1 Ω |
| E22-3 (OX1B) - E26-101 (OX1B) | Always | Below 1 Ω |
| E22-4 (E2) - E26-102 (EX1B) | Always | Below 1 Ω |
| E20-1 (HT2B) - E26-22 (HT2B) | Always | Below 1 Ω |
| E20-3 (OX2B) - E26-133 (OX2B) | Always | Below 1 Ω |
| E20-4 (E2) - E26-134 (EX2B) | Always | Below 1 Ω |
| E22-1 (HT1B) or E26-28 (HT1B) - Body ground | Always | 10 kΩ or higher |
| E22-3 (OX1B) or E26-101 (OX1B) - Body ground | Always | 10 kΩ or higher |
| E20-1 (HT2B) or E26-22 (HT2B) - Body ground | Always | 10 kΩ or higher |
| E20-3 (OX2B) or E26-133 (OX2B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern.
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | ||
| ||
| 15.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern.
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0138, P0156 OR P0158) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0136, P0138, P0156 or P0158.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (DTC P0136, P0138, P0156 or P0158 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | ||
| ||