Home › Engine / Hybrid System ยท 1AZ-FE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REASSEMBLY

for Preparation Click here



1. INSTALL RING PIN


    A128230E06
  1. Using a plastic-faced hammer, tap in new ring pins to the specified protrusion height.

    Standard protrusion height:
    3 mm (0.118 in.)

    Text in Illustration 
    *a
    Upper Side



2. INSTALL STUD BOLT

NOTICE:
If any of the stud bolts is deformed or the threads are damaged, replace it.



  1. Using E5 and E7 "TORX" sockets, install the stud bolts.


    A128231E12


    Text in Illustration 
    *a
    Front Side
    *b
    Upper Side
    *c
    Intake Side
    *c
    Exhaust Side

    Torque:
    Bolt A, B:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Bolt C, D:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }



3. INSTALL NO. 1 STRAIGHT HEAD SCREW PLUG


    A062841
  1. Using a 14 mm straight hexagon wrench, install 2 new gaskets and the 2 No. 1 straight head screw plugs.

    Torque:
    86 N*m{ 879 kgf*cm , 64 ft.*lbf }



4. INSTALL VALVE SPRING SEAT


    A062872
  1. Install the 16 valve spring seats to the cylinder head.



5. INSTALL VALVE STEM OIL SEAL


    A052449E07
  1. Apply a light coat of engine oil to a new oil seal.

    NOTICE:
    Pay close attention when installing the intake and exhaust oil seals. Installing the intake oil seal into the exhaust side or installing the exhaust oil seal into the intake side may cause installation problems later.

    HINT:
    The intake valve oil seal is gray and the exhaust valve oil seal is black.

    Text in Illustration 
    *a
    Intake Side
    *b
    Exhaust Side
    *c
    Gray
    *d
    Black



    A129854E06
  1. Using SST, push in the oil seal.

    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.

    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT



6. INSTALL INTAKE VALVE


    A094935E04
  1. Apply a sufficient coat of engine oil to the tip area of the intake valve shown in the illustration.

  1. Install the intake valve, compression spring and valve spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.



    A128225E05
  1. Using SST and wooden blocks, compress the compression spring and install the 2 valve retainer locks.

    SST
    09202-70020   (09202-00010)
    Text in Illustration 
    *1
    Wooden Block



    A036640E02
  1. Using a 5 mm pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the valve stem tip.

    Text in Illustration 
    *1
    5 mm Pin Punch



7. INSTALL EXHAUST VALVE


    A094936E04
  1. Apply a sufficient coat of engine oil to the tip area of the exhaust valve shown in the illustration.

  1. Install the exhaust valve, compression spring and valve spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.



    A128226E05
  1. Using SST and wooden blocks, compress the compression spring and install the 2 valve retainer locks.

    SST
    09202-70020   (09202-00010)
    Text in Illustration 
    *1
    Wooden Block



    A036641E03
  1. Using a 5 mm pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the valve stem tip.

    Text in Illustration 
    *a
    5 mm Pin Punch



8. INSTALL VALVE LIFTER
  1. Apply a light coat of engine oil.



    A062842E01
  1. Assemble the valve lifter and the tip of the valve stem.

    NOTICE:
    Install the same parts in the same combination to the original locations.