Home › Brake › PARKING BRAKE › PARKING BRAKE PEDAL (for RHD)

PARKING BRAKE PEDAL (for RHD) > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    C240128E01
  1. Install the parking brake control pedal assembly with the bolt and 2 nuts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Tighten the bolt and 2 nuts in the order shown in the illustration.

  1. Connect the parking brake switch connector.



    C240145
  1. Install the No. 1 parking brake cable assembly with the bolt.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Install the clip to the No. 1 parking brake cable assembly.



    C240121E01
  1. Temporarily install the lock nut.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut

    HINT:
    After adjusting parking brake pedal travel, tighten the lock nut.



2. CONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY


    C240122E02
  1. Connect the No. 4 parking brake cable assembly to the parking brake control pedal assembly as shown in the illustration.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



3. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

HINT:
Use the same procedure as for the LH side .



4. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

HINT:
Use the same procedure as for the LH side .



5. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
  1. Engage the 2 claws to install the No. 2 air duct sub-assembly.

  1. Install the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



6. INSTALL COMBINATION METER ASSEMBLY

HINT:
Use the same procedure as for the LH side .



7. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B280330
  1. Temporarily install the instrument cluster finish panel assembly as shown in the illustration.

  1. Connect each connector.

  1. for LHD:

    1. Engage the 3 claws, 7 clips and 4 guides.

  1. for RHD:

    1. Engage the 4 claws, 5 clips and 4 guides.



    B283375
  1. Engage the 4 clips and 2 guides to install the instrument cluster finish panel assembly.



8. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

HINT:
Use the same procedure as for the LH side .



9. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL
  1. w/ Smart Entry and Start System:

    1. Connect the connector.



    B281783
  1. Engage the 2 claws and 4 clips to install the upper instrument panel finish panel.



10. INSTALL AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



  1. Using SST, install the airbag sensor assembly with the 3 bolts.


    B278815E01

    SST
    09961-00950  

    Text in Illustration 
    *1
    Waterproof Sheet
    -
    -
    *a
    Fulcrum Length
    -
    -

    Torque:
    without SST:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }
    with SST:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.
    3. If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    4. When installing the airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    5. When the ignition switch is first turned to ON after the airbag sensor assembly has been replaced, make sure that no one is in the vehicle.

  1. Connect the connectors to the airbag sensor assembly as shown in the illustration.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Check that the waterproof sheet is properly set.

  1. Check that there is no looseness in the installation parts of the airbag sensor assembly.



11. INSTALL FLOOR CARPET BRACKET RH
  1. Engage the 2 guides.

  1. Install the floor carpet bracket RH with the 2 clips.



12. INSTALL NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (for Built-in Type Yaw Rate Sensor)
w/ Smart Entry and Start System:


13. INSTALL YAW RATE SENSOR BRACKET (for Separate Type Yaw Rate Sensor)


    C247856
  1. Install the yaw rate sensor bracket with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Engage the 2 clamps to install the wire harnesses.



14. INSTALL NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (for Separate Type Yaw Rate Sensor)
w/ Smart Entry and Start System:


15. INSTALL YAW RATE SENSOR (for Separate Type Yaw Rate Sensor)


    C247855E01
  1. Install the yaw rate sensor to the yaw rate sensor bracket with the 2 nuts.
    Text in Illustration 
    *a
    Arrow Mark

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    NOTICE:
    1. Do not damage the yaw sensor.
    2. Make sure that the yaw rate sensor is installed securely.
    3. Do not use dropped or damaged parts.
    4. Keep the contact surfaces of the yaw rate sensor and yaw rate sensor bracket free of foreign matter.
    5. Make sure that the connector end of the yaw rate sensor is facing in the same direction as the arrow mark on the bracket when installing the yaw rate sensor.

  1. Connect the connector to the yaw rate sensor.

    NOTICE:
    Make sure that the yaw rate sensor connector is connected securely.



16. INSTALL SHIFT LEVER SUPPORT

HINT:
Use the same procedure as for the LH side (Click here).



17. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



18. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD


19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



20. PERFORM DIAGNOSTIC SYSTEM CHECK
for Separate Type Yaw Rate Sensor: (Click here)
for Built-in Type Yaw Rate Sensor: (Click here)


21. INSPECT SRS WARNING LIGHT
for Separate Type Yaw Rate Sensor: (Click here)
for Built-in Type Yaw Rate Sensor: (Click here)


22. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Completely release the parking brake pedal.



    C240120E01
  1. Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut

  1. Remove the rear wheels.

  1. Temporarily install the hub nuts to the hub bolts.

    HINT:
    Securely install the hub nuts to the rear disc.

  1. Remove the parking brake shoes adjusting hole plug.



    C239414
  1. Turn the shoe adjuster and expand the shoes until the disc locks.
    Text in Illustration 
    V100135
    Expand
    V100136
    Contract

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Returns 8 notches.

  1. Check that there is no brake drag against the shoes.

  1. Install the parking brake shoe adjusting hole plug.

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    7 to 10 notches at 300 N (31 kgf, 67.5 lbf)

  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check that the parking brake does not drag.

  1. Remove the hub nuts from the hub bolts.

  1. Install the rear wheels.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



23. INSPECT BRAKE WARNING LIGHT
  1. When operating the parking brake pedal, check that the brake warning light illuminates.

    Standard:
    The brake warning light always illuminates at the first click.