Home › Drivetrain · U241E AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER

SHIFT LEVER > INSPECTION

for Preparation Click here



1. INSPECT LOWER SHIFT LEVER ASSEMBLY


    C239820E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (ACC) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V
    8 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V
    5 (KLS+) - Body ground
    Ignition switch ACC and shift lever in P
    Below 1 V
    Ignition switch ACC and shift lever except in P
    11 to 14 V
    4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Shift Lock Control ECU)

    HINT:
    Do not disconnect the lower shift lever assembly connector.



    C239820E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Value
    7 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Shift Lock Control ECU)

    HINT:
    Do not disconnect the lower shift lever assembly connector.



  1. Inspect shift lock solenoid



      C239826
    1. Disconnect the shift lock solenoid connector.



    2. C197452E09
    3. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

      Standard Resistance:
      Tester Connection
      Shift Lever Position
      Specified Condition
      4 (P) - 3 (E2)
      P
      10 kΩ or higher
      Other than P
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Shift Lock Solenoid)
      1. If the result is not as specified, replace the lower shift lever assembly.
      2. If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (SLS+) - 2 (SLS-)
      Always
      112 Ω

      1. If the result is not as specified, replace the lower shift lever assembly.
      2. If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.



2. INSPECT TRANSMISSION CONTROL SWITCH


    C239095E09
  1. Measure the resistance between each terminal of the shift lock control unit assembly when the shift lever is moved to each position.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (IG) - 5 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    Shift lever not in S, "+" or "-"
    10 kΩ or higher
    3 (SFTU) - 2 (E)
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    Shift lever not held in "+"
    10 kΩ or higher
    1 (SFTD) - 2 (E)
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    Shift lever not held in "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)
    If the resistance value is not as specified, replace the lower shift lever assembly.