DTC P2808 Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2808 | The engine revs freely when 3rd or 5th gear is commanded. (2-trip detection logic) When any of the following is detected. In addition, the condition that 4th gear is engaged when 4th gear is commanded occurs twice. (2-trip detection logic)
|
|
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2808) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / DTC.
Read the DTCs using the intelligent tester.
| Display (DTC output) | Proceed to |
| Only "P2808" is output | A |
| "P2808" and other DTCs are output | B |
|
| ||||
| B | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Details | Control Range | Diagnostic Note |
| Control the Shift Position | Operates the shift solenoid valves to allow gears to selected manually. |
| Can be used to check the operation of the shift solenoid valves. Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (31 mph) or less |
Check the vehicle speed and the gear when the engine speed is 1000 rpm.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the TCM commanded gear and the actual gear.
| Actuator Gear during Malfunction | TCM Commanded Gear | Proceed to | ||||||
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid SL4 | Stuck ON*3 | 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid SLT | Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E |
| Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| D | |
| 3.INSPECT SHIFT SOLENOID VALVE SL4 |
![]() |
Remove shift solenoid valve SL4.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
| *1 | Shift Solenoid Valve SL4 |
Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||