Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

POWER STEERING SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA

NOTICE:
  1. It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
  2. Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester.

  1. Turn the ignition switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the intelligent tester on.

  5. Check the freeze frame data on the intelligent tester.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from meter/
    Min.: 0.0 km/h (0.0 mph)
    Max.: 300.0 km/h (186.4 mph)
    0 km/h (0 mph)
    Engine running and vehicle stopped
    No significant fluctuation
    Engine running and vehicle driven at a constant speed
    Engine Revolution
    Engine speed/
    Min.: 0 rpm
    Max.: 12800 rpm
    No significant fluctuation
    Engine running at a constant speed
    Motor Actual Current*1
    Current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    - The value increases when turning right and decreases when turning left
    Engine running and steering wheel being turned
    Motor Actual Current*2
    Current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    - The value increases when turning left and decreases when turning right
    Engine running and steering wheel being turned
    Command Value Current*1
    Requested current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    - The value increases when turning right and decreases when turning left
    Engine running and steering wheel being turned
    Command Value Current*2
    Requested current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    - The value increases when turning left and decreases when turning right
    Engine running and steering wheel being turned
    Steering Angle Velocity
    Steering angle speed/
    Min.: -32768 deg/s
    Max.: 32767 deg/s
    Value changes in proportion to steering speed
    - The value increases when turning left and decreases when turning right
    Engine running and steering wheel being turned
    Thermistor Temperature
    ECU substrate temperature/
    Min.: -50.0°C (-58.0°F)
    Max.: 150.0°C (302.0°F)
    -50°C to 150°C (-58°F to 302°F)
    -
    PIG Power Supply
    Power source voltage to active motor/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Always
    IG Power Supply
    ECU power source voltage/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Ignition switch ON
    Steering Wheel Torque
    Steering wheel torque/
    Min.: -327.68 Nm
    Max.: 7.00 Nm
    Value changes in proportion to steering effort
    - The value increases when turning left and decreases when turning right
    Engine running and steering wheel being turned
    Motor Rotation Angle
    Motor rotation angle/
    Min.: 0.000 deg
    Max.: 1441.770 deg
    During steering operation, motor rotation angle value changes from 0 to 360°
    Engine running and steering wheel being turned
    Command Val Current 2*1
    Requested current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    - The value increases when turning left and decreases when turning right
    Engine running and steering wheel being turned
    Command Val Current 2*2
    Requested current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    - The value increases when turning right and decreases when turning left
    Engine running and steering wheel being turned
    Motor Voltage
    Motor power supply voltage/
    Min.: 0.000 V
    Max.: 98.000 V
    9 to 16 V
    Always
    Motor Terminal Volt (U)
    Motor terminal voltage (U phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 16 V range
    Engine running and steering wheel being turned
    Motor Terminal Volt (V)
    Motor terminal voltage (V phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 16 V range
    Engine running and steering wheel being turned
    Motor Terminal Volt (W)
    Motor terminal voltage (W phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 16 V range
    Engine running and steering wheel being turned
    Torque Sensor 1 Output
    Torque sensor voltage/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Engine running and steering wheel not being turned (without load)
    2.5 to 3.8 V
    Engine running and steering wheel being turned to the right with vehicle stopped
    1.2 to 2.5 V
    Engine running and steering wheel being turned to the left with vehicle stopped
    Torque Sensor 2 Output
    Torque sensor voltage/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Engine running and steering wheel not being turned (without load)
    1.2 to 2.5 V
    Engine running and steering wheel being turned to the right with vehicle stopped
    2.5 to 3.8 V
    Engine running and steering wheel being turned to the left with vehicle stopped
    TRQ1 Zero Point Value
    Torque sensor voltage/
    Min.: 0.0000 V
    Max.: 4.9725 V
    Values differ depending on vehicle
    Engine running and steering wheel not being turned
    TRQ2 Zero Point Value
    Torque sensor voltage/
    Min.: 0.0000 V
    Max.:4.9725 V
    Values differ depending on vehicle
    Engine running and steering wheel not being turned
    PS Assist Signal
    Status of the Record of Power Steering Assist Signal/
    OFF or ON
    OFF
    Ignition switch ON
    ON
    Engine running

HINT:
  1. *1: for LHD
  2. *2: for RHD