DIFFERENTIAL CASE > REASSEMBLY |
| 1. INSTALL DIFFERENTIAL SIDE GEAR |
![]() |
Coat the 2 front differential side gears, 2 No. 1 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.
| 2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT |
![]() |
Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.
| 3. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH |
![]() |
Hold the differential case in a vise between aluminum plates.
Place a dial indicator on the tip of the side gear tooth at a right angle.
Hold the pinion gear in the differential case and measure the backlash of the side gear.
| Thickness [mm (in.)] |
| 1.00 (0.0394) |
| 1.10 (0.0433) |
| 1.20 (0.0472) |
| 1.30 (0.0512) |
| 4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN |
![]() |
Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin.
![]() |
Using a chisel and hammer, stake the differential case.
| 5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, install a new front differential case rear tapered roller bearing to the front differential case.
![]() |
Using SST and a hammer, install a new front differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.
| 6. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, install a new front differential case front tapered roller bearing to the front differential case.
![]() |
Install the shim to the transaxle housing.
Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle housing.
| 7. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD |
Remove packing material from the contact surfaces between the transaxle housing and case.
![]() |
Install the differential assembly to the transaxle case sub-assembly.
![]() |
Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.
![]() |
Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.
| Thickness | Thickness | Thickness | Thickness |
| 2.000 (0.0787) | 2.225 (0.0876) | 2.450 (0.0965) | 2.675 (0.105) |
| 2.025 (0.0797) | 2.250 (0.0886) | 2.475 (0.0974) | 2.700 (0.106) |
| 2.050 (0.0807) | 2.275 (0.0896) | 2.500 (0.0984) | 2.725 (0.107) |
| 2.075 (0.0817) | 2.300 (0.0906) | 2.525 (0.0994) | 2.750 (0.108) |
| 2.100 (0.0827) | 2.325 (0.0915) | 2.550 (0.100) | 2.775 (0.109) |
| 2.125 (0.0837) | 2.350 (0.0925) | 2.575 (0.101) | 2.800 (0.110) |
| 2.150 (0.0846) | 2.375 (0.0935) | 2.600 (0.102) | 2.825 (0.111) |
| 2.175 (0.0856) | 2.400 (0.0945) | 2.625 (0.103) | 2.850 (0.112) |
| 2.200 (0.0866) | 2.425 (0.0955) | 2.650 (0.104) | 2.875 (0.113) |
![]() |
Remove the 20 bolts and the transaxle housing from the transaxle case sub-assembly.
![]() |
Remove the front differential case from the transaxle case sub-assembly.
| 8. INSTALL FRONT DIFFERENTIAL RING GEAR |
![]() |
Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).
![]() |
Clean the contact surface of the front differential case.
Align the matchmarks, set the front differential ring gear to the front differential case.
| *a | Matchmark |
![]() |
Install the 12 bolts.
| 9. INSTALL TRANSAXLE CASE OIL SEAL |
![]() |
Coat the lip of a new transaxle case oil seal with a small amount of MP grease.
Using SST and a hammer, tap in the transaxle case oil seal.
| 10. INSTALL FRONT TRANSAXLE CASE OIL SEAL |
![]() |
Coat the lip of a new front transaxle case oil seal with a small amount of MP grease.
Using SST and a hammer, tap in the front transaxle case oil seal.