Home › Drivetrain ยท U660E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > REASSEMBLY

for Preparation Click here



1. INSTALL DIFFERENTIAL SIDE GEAR


    C138528
  1. Coat the 2 differential side gears, 2 No. 1 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.



2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT


    C138706
  1. Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.



3. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH


    C083562
  1. Hold the differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Place a dial indicator at a right angle to one of the side gear teeth.

  1. Hold the pinion gear in the differential case and measure the backlash of the side gear.

    Standard backlash:
    0.05 to 0.15 mm (0.00197 to 0.00591 in.)

    Thrust Washer Thickness 
    Thickness
    Thickness
    1.50 mm (0.0591 in.)
    1.75 mm (0.0689 in.)
    1.55 mm (0.0610 in.)
    1.80 mm (0.0709 in.)
    1.60 mm (0.0630 in.)
    1.85 mm (0.0728 in.)
    1.65 mm (0.0650 in.)
    1.90 mm (0.0748 in.)
    1.70 mm (0.0669 in.)
    -
    If the backlash is not within the standard range, select another side gear thrust washer.



4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN


    C138707
  1. Using a pin punch (3 mm) and hammer, install the front differential pinion shaft straight pin.

    NOTICE:
    Align the holes, and install the pinion shaft straight pin.



    C138711
  1. Using a chisel and hammer, stake the differential case.

    NOTICE:
    Stake the differential case after adjusting the backlash.



5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    C138712E01
  1. Using SST and a press, install a new front differential case rear tapered roller bearing to the differential case.

    SST
    09726-36010  
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage during bearing inner race installation.



    C196828E01
  1. Using SST and a hammer, install a new front differential case rear tapered roller bearing outer race to the transaxle case sub-assembly.

    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)

    NOTICE:
    Ensure that there is no clearance between the bearing and transaxle case sub-assembly.



6. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    C196829E01
  1. Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.

    SST
    09710-30012   (09710-04081)
    09950-60010   (09951-00480)
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage during bearing inner race installation.

  1. Install the shim to the transaxle housing.



    C196830E01
  1. Using SST and a hammer, install a new front differential case front tapered roller bearing outer race to the transaxle housing.

    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)

    NOTICE:
    Ensure that there is no clearance between the bearing and transaxle housing.



7. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD


    C136467
  1. Install the differential assembly to the transaxle case sub-assembly.

  1. Clean the contact surfaces of the transaxle case and transaxle housing.



    C136447E01
  1. Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

    Torque:
    Bolt A:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }
    Bolt B:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }



    C138262E01
  1. Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearings.

    SST
    09564-33010  

  1. Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.

    SST
    09564-33010  

    Turning torque:
    1.1 to 1.9 N*m (11 to 19 kgf*cm, 10 to 17 in.*lbf)

    If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.
    Shim Thickness: mm (in.) 
    Thickness
    Thickness
    Thickness
    Thickness
    2.000 (0.0787)
    2.225 (0.0876)
    2.450 (0.0965)
    2.675 (0.105)
    2.025 (0.0797)
    2.250 (0.0886)
    2.475 (0.0974)
    2.700 (0.106)
    2.050 (0.0807)
    2.275 (0.0896)
    2.500 (0.0984)
    2.725 (0.107)
    2.075 (0.0817)
    2.300 (0.0906)
    2.525 (0.0994)
    2.750 (0.108)
    2.100 (0.0827)
    2.325 (0.0915)
    2.550 (0.100)
    2.775 (0.109)
    2.125 (0.0837)
    2.350 (0.0925)
    2.575 (0.101)
    2.800 (0.110)
    2.150 (0.0846)
    2.375 (0.0935)
    2.600 (0.102)
    2.825 (0.111)
    2.175 (0.0856)
    2.400 (0.0945)
    2.625 (0.103)
    2.850 (0.112)
    2.200 (0.0866)
    2.425 (0.0955)
    2.650 (0.104)
    2.875 (0.113)



    C136447E04
  1. Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.



    C136467
  1. Remove the differential assembly from the transaxle case sub-assembly.



8. INSTALL FRONT DIFFERENTIAL RING GEAR


    D025215
  1. Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

    NOTICE:
    Do not heat the ring gear to more than 110°C (230°F).

  1. Clean the contact surface of the front differential case.



    C138531E08
  1. Align the matchmarks, and install the front differential ring gear case quickly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Do not install the bolts while the ring gear is hot.



    C138532
  1. Install and tighten the 12 bolts.

    Torque:
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }

    NOTICE:
    Tighten the bolts a little at a time in a diagonal sequence.



9. INSTALL TRANSAXLE CASE OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.



    C196831E01
  1. Using SST and a hammer, install the transaxle case oil seal.

    SST
    09316-10010  
    09950-70010   (09951-07100)

    Oil seal driven in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Check that the oil seal is installed in the correct direction.



10. INSTALL FRONT TRANSAXLE CASE OIL SEAL


    C188707E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, install the front transaxle case oil seal.

    SST
    09308-14010  

    Oil seal driven in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Check that the oil seal is installed in the correct direction.