Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0660    Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)

for Preparation Click here


DESCRIPTION


A255384E01


Text in Illustration 
*1
Intake Air Control Valve Open
*2
Intake Air Control Valve Closed
This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

DTC No.
DTC Detection Condition
Trouble Area
P0660
The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
  1. The voltage of terminal ACIS of the ECM is low when the vacuum switching valve assembly (for acoustic control induction system) is off.
  2. The engine has been started.
  1. Open or short in vacuum switching valve assembly (for acoustic control induction system) circuit
  2. Vacuum switching valve assembly (for acoustic control induction system)
  3. No. 1 integration relay
  4. ECM

WIRING DIAGRAM


A266828E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR INTAKE CONTROL)


    A204525E02
  1. Disconnect the vacuum hose from port F on the vacuum switching valve assembly (for acoustic control induction system).
    Text in Illustration 
    *1
    Port F
    *2
    Port E
    *a
    ON
    *b
    OFF
    *c
    Air

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

  1. Operate the vacuum switching valve assembly (for acoustic control induction system) check the air flow.

    Standard:
    Activate the VSV for Intake Control
    Specified Condition
    ON
    Air from port E flows out through port F
    OFF
    Air from port E flows out through air filter

    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B

    HINT:
    Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)
  1. Inspect the vacuum switching valve assembly (for acoustic control induction system) (Click here).



NG
REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) (Click here)
OK


3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))


    A194112E41
  1. Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E45-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vacuum Switching Valve Assembly (for Acoustic Control Induction System))



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) - ECM)
  1. Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E45-1 (ACIS) - E26-69 (ACIS)
    Always
    Below 1 Ω
    E45-1 (ACIS) or E26-69 (ACIS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1A-8 - E45-2 (+B)
    Always
    Below 1 Ω
    1A-8 or E45-2 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)