Home › Power Source / Network ยท NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > SYSTEM DIAGRAM

for Preparation Click here



OVERALL CAN BUS DIAGRAM (for LHD)


  1. Control system CAN is composed of 2 buses.


    C249205E01


    Text in Illustration 
    *1
    V Bus
    *2
    Sub Bus 1
    *3
    V Bus Terminating Resistor
    *4
    Sub Bus 1 Terminating Resistor
    *5
    Combination Meter Assembly
    (for V Bus)
    *6
    AFS ECU*4
    (for V Bus)
    *7
    Airbag Sensor Assembly
    (for V Bus)
    *8
    DLC3
    (for V Bus)
    *9
    Power Steering ECU with Motor Assembly
    (for V Bus)
    *10
    Main Body ECU (Multiplex Network Body ECU)
    (for V Bus and Sub Bus 1)
    *11
    Steering Sensor
    (for V Bus)
    *12
    Air Conditioning Amplifier Assembly
    (for V Bus)
    *13
    Clearance Warning ECU Assembly*5
    (for V Bus)
    *14
    Brake Actuator Assembly
    (for V Bus)
    *15
    Smart Key ECU Assembly (Certification ECU)*3
    (for V Bus)
    *16
    1. Navigation ECU Sub-assembly*1
    2. Radio and Display Receiver Assembly*2
    (for V Bus)
    *17
    Yaw Rate Sensor*7
    (for V Bus)
    *18
    ECM
    (for V Bus)
    *19
    Multiplex Tilt and Telescopic ECU*6
    (for Sub Bus 1)
    *20
    CAN No. 5 J/C*6
    (for Sub Bus 1)
    *1: for Navigation receiver type
    *2: for Radio and display type
    *3: w/ Smart entry and start system
    *4: w/ AFS
    *5: w/ Toyota parking assist-sensor system
    *6: w/ Power tilt and power telescopic steering column system
    *7: Separate type yaw rate sensor

HINT:
  1. The main body ECU (multiplex network body ECU) functions as a gateway between the V bus and sub bus 1.
  2. Refer to the following bus wiring diagrams for details.


V BUS (for LHD)

C240999E02


C249206E02

HINT:
The CAN communication system connects to other networks via ECUs that function as a gateway (Click here).


SUB BUS 1 (w/ Power Tilt and Power Telescopic Steering Column System for LHD)

C241003E03


OVERALL CAN BUS DIAGRAM (for RHD)


  1. Control system CAN is composed of 1 bus.


    C249207E01


    Text in Illustration 
    *1
    V Bus
    *2
    V Bus Terminating Resistor
    *3
    ECM
    (for V Bus)
    *4
    Main Body ECU (Multiplex Network Body ECU)
    (for V Bus)
    *5
    Airbag Sensor Assembly
    (for V Bus)
    *6
    Power Steering ECU with Motor Assembly
    (for V Bus)
    *7
    Air Conditioning Amplifier Assembly
    (for V Bus)
    *8
    Radio and Display Receiver Assembly
    (for V Bus)
    *9
    Steering Sensor
    (for V Bus)
    *10
    Smart Key ECU Assembly (Certification ECU)*1
    (for V Bus)
    *11
    Brake Actuator Assembly
    (for V Bus)
    *12
    Clearance Warning ECU Assembly
    (for V Bus)
    *13
    DLC3
    (for V Bus)
    *14
    Yaw Rate Sensor*2
    (for V Bus)
    *15
    Combination Meter Assembly
    (for V Bus)
    -
    -
    *1: w/ Smart entry and start system
    *2: Separate type yaw rate sensor

    HINT:
    Refer to the following bus wiring diagrams for details.


V BUS (for RHD)

C241001E02


C249209E01

HINT:
The CAN communication system connects to other network via ECUs that function as a gateway (Click here).