Home › Drivetrain ยท U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE BREATHER PLUG HOSE


    C190663
  1. Using a screwdriver, remove the breather plug hose from the transaxle case sub-assembly.



    C134952E04
  1. Using a screwdriver, remove the No. 1 breather plug (ATM) and No. 2 breather plug (ATM) from the breather plug hose.
    Text in Illustration 
    *1
    No. 1 Breather Plug (ATM)
    *2
    Breather Plug Hose
    *3
    No. 2 Breather Plug (ATM)
    *4
    O-ring

  1. Using a screwdriver, remove the O-ring from the No. 2 breather plug (ATM).



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C136685
  1. Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft.



    C136686
  1. Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.

    NOTICE:
    Before removing the park/neutral position switch, remove any dirt or rust on the installation portion of the manual valve lever shaft. Be sure to remove the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.



3. REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)


    C239730
  1. Remove the oil cooler tube union (outlet oil cooler union) from the transaxle case sub-assembly.

  1. Remove the O-ring from the oil cooler tube union (outlet oil cooler union).



4. REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)


    C239679
  1. Remove the oil cooler tube union (inlet oil cooler union) from the transaxle case sub-assembly.

  1. Remove the O-ring from the oil cooler tube union (inlet oil cooler union).



5. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C134958
  1. Remove the 3 No. 1 transaxle case plugs from the transaxle case sub-assembly.

  1. Using a screwdriver, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.



    C134959
  1. Using a hexagon socket wrench (6 mm), remove the 3 hexagon bolts from the transaxle housing.

  1. Remove the gasket from each of the 3 hexagon bolts.



6. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY


    C136444
  1. Support the transaxle assembly on wooden blocks.



7. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C134961
  1. Using a hexagon socket wrench (6 mm), remove the overflow plug from the automatic transaxle oil pan sub-assembly.

  1. Remove the gasket from the overflow plug.



    C141531
  1. Using a hexagon socket wrench (6 mm), remove the No. 1 transmission oil filler tube from the automatic transaxle assembly.



    C134962
  1. Remove the 18 bolts, automatic transaxle oil pan sub-assembly and automatic transaxle oil pan gasket from the automatic transaxle assembly.



    C134963E04
  1. Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.
    Text in Illustration 
    *1
    Magnet



8. INSPECT TRANSMISSION OIL CLEANER MAGNET


    C138722
  1. Use the removed magnets to collect any steel chips. Examine the chips and particles in the pan and on the magnets to determine what type of wear has occurred in the transaxle:

    Result:
    Steel (magnetic):
    Bearing, gear and plate wear
    Brass (non-magnetic):
    Bushing wear



9. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    C136687
  1. Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.



    C136688E04
  1. Remove the O-ring from the valve body oil strainer assembly.
    Text in Illustration 
    *1
    O-ring



10. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C136689
  1. Remove the 11 bolts and transmission valve body assembly from the transaxle case sub-assembly.

    NOTICE:
    When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and the transaxle case sub-assembly to interfere with each other.



11. REMOVE TRANSAXLE CASE GASKET


    C136429E01
  1. Remove the 2 gaskets from the transaxle case sub-assembly.



12. INSPECT INPUT SHAFT SUB-ASSEMBLY


    C136696
  1. Using a dial indicator, measure the input shaft end play.

    End play:
    0.012 to 1.250 mm (0.000473 to 0.0492 in.)



13. REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY


    C136430
  1. Remove the refill plug from the rear transaxle cover sub-assembly.

  1. Remove the gasket from the refill plug.



    C134960
  1. Remove the 2 No. 1 automatic transaxle case plugs from the rear transaxle cover sub-assembly.

  1. Using a screwdriver, remove the 2 O-rings from the 2 No. 1 automatic transaxle case plugs.



    C162440E02
  1. Remove the 14 bolts from the rear transaxle cover sub-assembly.

  1. Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case sub-assembly.



    C136432E01
  1. Using a screwdriver, remove the 3 O-rings from the transaxle case sub-assembly.



    C162441E03
  1. Using a screwdriver, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.
    Text in Illustration 
    *1
    Oil Seal Ring
    *2
    Thrust Needle Roller Bearing
    *3
    Thrust Needle Roller Race

  1. Remove the thrust needle roller bearing and thrust needle roller race from the rear transaxle cover sub-assembly.



    C162442E01
  1. Using a "TORX" socket wrench (T30), remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.



    C194888E05
  1. Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09319-60020  



14. REMOVE DIRECT MULTIPLE DISC CLUTCH ASSEMBLY


    C136442E02
  1. Remove the direct multiple disc clutch assembly from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Direct Multiple Disc Clutch Assembly
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing from the direct multiple disc clutch assembly.



15. REMOVE DIRECT MULTIPLE DISC CLUTCH SNAP RING


    C136433
  1. Using a screwdriver, remove the snap ring from the direct multiple disc clutch assembly.



    C136434
  1. Remove the No. 2 direct clutch piston from the direct multiple disc clutch assembly.



    C136428E04
  1. Using a screwdriver, remove the intermediate shaft oil seal from the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Intermediate Shaft Oil Seal
    *2
    O-ring

  1. Using a screwdriver, remove the O-ring from the direct multiple disc clutch assembly.



16. REMOVE NO. 2 CLUTCH DISC


    C136435E03
  1. Remove the clutch flange, 3 clutch discs and 3 clutch plates from the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Clutch Plate
    *2
    Clutch Disc
    *3
    Clutch Flange



17. INSPECT NO. 2 CLUTCH DISC


    C138267
  1. Check if the contact surfaces of the discs, plates and flange are worn or burnt.

    NOTICE:
    1. If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



18. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    C136436
  1. Using a snap ring expander, remove the snap ring from the direct multiple disc clutch assembly.



    C136437
  1. Remove the rear planetary sun gear assembly from the direct multiple disc clutch assembly.



    C136438E05
  1. Remove the thrust needle roller bearing and thrust needle roller race from the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race



19. INSPECT REAR PLANETARY SUN GEAR ASSEMBLY


    C138266
  1. Using a dial indicator, measure the inside diameter of the bushing of the rear planetary sun gear sub-assembly.

    Standard inside diameter:
    25.580 to 25.601 mm (1.0071 to 1.0079 in.)

    Maximum inside diameter:
    25.601 mm (1.0079 in.)

    If the inside diameter is greater than the maximum, replace the rear planetary sun gear assembly.



20. REMOVE NO. 1 CLUTCH DISC


    C136445
  1. Using 2 screwdrivers, remove the 2 snap rings from the direct multiple disc clutch assembly.



    C136446E03
  1. Remove the clutch flange, 4 clutch discs and 4 clutch plates from the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Clutch Flange
    *2
    Clutch Plate
    *3
    Clutch Disc



21. INSPECT NO. 1 CLUTCH DISC


    C138265
  1. Check if the contact surfaces of the discs, plates and flange are worn or burnt.

    NOTICE:
    1. If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



22. REMOVE TRANSAXLE HOUSING


    C136447E04
  1. Remove the 20 bolts from the transaxle housing.

  1. Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case sub-assembly.



23. REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE


    C194889E01
  1. Using SST, remove the counter driven gear front tapered roller bearing outer race and shim from the transaxle housing.

    SST
    09308-00010  



24. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    C136449E01
  1. Remove the bolt, clamp and differential gear lube apply tube from the transaxle housing.



25. REMOVE FRONT OIL PUMP ASSEMBLY


    C136450E02
  1. Remove the 7 bolts and front oil pump from the transaxle case sub-assembly.

  1. Remove the O-ring from the front oil pump assembly.
    Text in Illustration 
    *1
    O-ring



    C138729E04
  1. Remove the thrust needle roller bearing and thrust needle roller race from the carrier lock nut.

  1. Remove the O-ring from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race
    *3
    O-ring



26. REMOVE FRONT OIL PUMP BODY O-RING


    C138278
  1. Remove the O-ring from the front oil pump body sub-assembly.



27. REMOVE NO. 3 BRAKE DISC


    C136451E03
  1. Using a screwdriver, remove the snap ring from the oil pump assembly.
    Text in Illustration 
    *1
    Snap Ring



    C136452E02
  1. Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates from the oil pump assembly.
    Text in Illustration 
    *1
    No. 3 Brake Flange
    *2
    No. 3 Brake Plate
    *3
    No. 3 Brake Disc



28. INSPECT NO. 3 BRAKE DISC


    C138255
  1. Check if the contact surfaces of the discs, plates and flanges are worn or burnt.

    NOTICE:
    1. If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



29. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C136458
  1. Remove the underdrive planetary gear assembly from the front oil pump assembly.



30. REMOVE NO. 3 BRAKE HUB


    C136454
  1. Remove the No. 3 brake hub from the underdrive planetary gear assembly.



    C136455E05
  1. Remove the thrust needle roller bearing and thrust needle roller race from the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Race
    *2
    Thrust Needle Roller Bearing



31. REMOVE UNDERDRIVE PLANETARY RING GEAR


    C136456E02
  1. Using needle-nose pliers, remove the snap ring from the underdrive planetary ring gear.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Underdrive Planetary Ring Gear

  1. Remove the underdrive planetary ring gear from the underdrive planetary gear assembly.



32. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY


    C136457E02
  1. While expanding the snap ring with snap ring pliers, remove the planetary sun gear from the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Planetary Sun Gear Sub-assembly
    *2
    Underdrive Planetary Gear Assembly
    *3
    Snap Ring

  1. Remove the snap ring from the underdrive planetary gear assembly.



33. INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C138260
  1. Using a feeler gauge, measure the clearance between the underdrive planetary gear and the pinion gear at 4 points.

    Standard clearance:
    0.18 to 0.54 mm (0.00709 to 0.0213 in.)

    If the clearance is greater than the standard clearance, replace the underdrive planetary gear.



34. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY


    C138259
  1. Using a dial indicator, measure the inside diameter of the bushings of the planetary sun gear.

    Standard inside diameter:
    25.525 to 25.546 mm (1.0049 to 1.0057 in.)

    Maximum inside diameter:
    25.546 mm (1.0057 in.)

    If the inside diameter is greater than the maximum, replace the planetary sun gear.



35. REMOVE INPUT SHAFT SUB-ASSEMBLY


    C136459
  1. Remove the input shaft sub-assembly from the front oil pump assembly.



    C136460E05
  1. Remove the thrust needle roller bearing and thrust needle roller race from the input shaft.
    Text in Illustration 
    *1
    Thrust Needle Roller Race
    *2
    Thrust Needle Roller Bearing
    *3
    Input Shaft Oil Seal Ring
    *4
    Input Shaft

  1. Using a screwdriver, remove the 3 input shaft oil seal rings from the input shaft.



36. REMOVE UNDERDRIVE PLANETARY SUN GEAR


    C136461E02
  1. Remove the underdrive planetary sun gear from the oil pump assembly.
    Text in Illustration 
    *1
    Underdrive Planetary Sun Gear
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing from the oil pump assembly.



37. REMOVE NO. 1 BRAKE DISC


    C153477E02
  1. Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the oil pump assembly.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Brake Snap Ring Stopper



    C136463E04
  1. Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the oil pump assembly.
    Text in Illustration 
    *1
    No. 1 Brake Flange
    *2
    No. 1 Brake Plate
    *3
    No. 1 Brake Disc



38. INSPECT NO. 1 BRAKE DISC


    C138255
  1. Check if the contact surfaces of the discs, plates and flange are worn or burnt.

    NOTICE:
    1. If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



39. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C136464
  1. Remove the 3 2nd brake piston return springs from the oil pump assembly.



40. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C138254
  1. Using a vernier caliper, measure the free length of the 3 2nd brake piston return springs including the spring seats.

    Standard free length:
    23.85 mm (0.939 in.)

    If the free length is shorter than the standard free length, replace the 2nd brake piston return spring.



41. REMOVE NO. 1 BRAKE PISTON


    C136465
  1. Holding the oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump assembly to remove the No. 1 brake piston.



    C136466E03
  1. Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.
    Text in Illustration 
    *1
    O-ring



42. REMOVE FRONT DIFFERENTIAL CASE


    C136467
  1. Remove the front differential case from the transaxle case sub-assembly.



43. REMOVE COUNTER DRIVE GEAR NUT


    C136698E01
  1. Using SST and a hammer, unstake the counter drive gear nut.

    SST
    09930-00010  



    C136700E01
  1. Turn the manual valve lever 2 notches counterclockwise to set it to the P position as shown in the illustration.



    C136468E01
  1. Using SST, remove the counter drive gear nut from the planetary gear assembly.

    SST
    09387-00130  



44. REMOVE COUNTER DRIVEN GEAR


    C136699E01
  1. Turn the manual valve lever 2 notches clockwise to set it to the N position as shown in the illustration.



    C136469
  1. Remove the counter driven gear from the transaxle case sub-assembly.



45. REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING


    C194890E03
  1. Using SST, remove the counter driven gear front tapered roller bearing from the counter driven gear.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00400)



46. REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING


    C194891E03
  1. Using SST, remove the counter driven gear rear tapered roller bearing and differential drive pinion from the counter driven gear.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
    09950-60010   (09951-00320)



47. REMOVE PAWL SHAFT CLAMP


    C136472
  1. Remove the bolt and pawl shaft clamp from the transaxle case sub-assembly.



48. REMOVE PAWL STOPPER PLATE


    C136473
  1. Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.



49. REMOVE PARKING LOCK SLEEVE


    C136474
  1. Remove the parking lock sleeve from the transaxle case sub-assembly.



50. REMOVE PARKING LOCK PAWL


    C136475E02
  1. Remove the spring, parking lock pawl pin, parking lock pawl shaft and parking lock pawl from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Parking Lock Pawl Shaft
    *2
    Parking Lock Pawl
    *3
    Spring
    *4
    Parking Lock Pawl Pin



51. REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE


    C194892E01
  1. Using SST, remove the counter driven gear rear tapered roller bearing outer race from the transaxle case sub-assembly.

    SST
    09308-00010  



52. REMOVE ONE-WAY CLUTCH ASSEMBLY


    C141525
  1. Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.



    C141526E02
  1. Remove the one-way clutch assembly with the planetary ring gear from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing from the planetary gear assembly.



53. INSPECT ONE-WAY CLUTCH ASSEMBLY


    C189425E05
  1. Temporarily install the one-way clutch assembly to the planetary ring gear.
    Text in Illustration 
    *1
    Planetary Ring Gear
    *2
    One-way Clutch Assembly
    *a
    Free
    *b
    Lock

  1. Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.
    If the one-way clutch assembly does not operate normally, replace it.



54. REMOVE PLANETARY RING GEAR


    C136479E02
  1. Remove the planetary ring gear from the one-way clutch assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Planetary Ring Gear



55. REMOVE PLANETARY RING GEAR FLANGE


    C136480E02
  1. Using a screwdriver, remove the snap ring from the planetary ring gear.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Planetary Ring Gear Flange
    *3
    Planetary Ring Gear

  1. Remove the planetary ring gear flange from the planetary ring gear.



56. REMOVE NO. 2 BRAKE DISC


    C141524
  1. Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.



    C136483E02
  1. Remove the brake flange, 5 brake discs and 5 brake plates from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Brake Flange
    *2
    Brake Plate
    *3
    Brake Disc



57. INSPECT NO. 2 BRAKE DISC


    C137438
  1. Check if the contact surfaces of the discs, plates and flange are worn or burnt.

    NOTICE:
    1. If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



58. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C136482
  1. Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.



    C136484
  1. Remove the 1st and reverse brake return spring from the transaxle case sub-assembly.



59. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C141533
  1. Using a vernier caliper, measure the free length of the 1st and reverse brake return spring together with the spring seat.

    Standard free length:
    15.79 mm (0.621 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring.



60. REMOVE NO. 2 BRAKE PISTON


    C136485
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston from the transaxle case sub-assembly.



    C136673E03
  1. Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.
    Text in Illustration 
    *1
    O-ring



61. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    C136674E01
  1. Using SST and a press, remove the planetary gear assembly from the transaxle case sub-assembly.

    SST
    09950-60010   (09951-00580)
    09950-70010   (09951-07100)



62. REMOVE COUNTER DRIVE GEAR

NOTICE:
Perform this procedure only when the counter drive gear bearing or transaxle case sub-assembly is replaced.



    C194893E01
  1. Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case sub-assembly.

    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)



    C136676
  1. As shown in the illustration, tighten the 3 bolts evenly and leave a clearance of approximately 20.0 mm (0.787 in.) between the counter drive gear and bearing inner race (front side).



    C194894E03
  1. Using SST, remove the bearing inner race (front side) from the counter drive gear.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-60020   (09951-00710)



63. REMOVE NO. 3 BRAKE PISTON


    C136678
  1. Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.



    C136679E02
  1. Remove the brake piston return spring from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Brake Piston Return Spring
    *2
    No. 3 Brake Piston

  1. Remove the No. 3 brake piston from the transaxle case sub-assembly.



64. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    C134953E01
  1. Remove the bolt, cover and manual detent spring sub-assembly from the transaxle case sub-assembly.



65. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    C136683
  1. Remove the parking lock rod sub-assembly from the parking lock lever sub-assembly.

    HINT:
    Align the slot with the notches on the parking lock lever sub-assembly to remove the parking lock rod sub-assembly.



66. REMOVE MANUAL VALVE LEVER SHAFT


    C136680E01
  1. Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the transaxle case sub-assembly.



    C136701
  1. Using a screwdriver, slide the spacer of the manual valve lever sub-assembly.



    C137417
  1. Using a pin punch (3 mm) and hammer, drive out the slotted spring pin from the manual valve lever sub-assembly.

    HINT:
    To prevent the pin from falling into the case, drive the pin until it has cleared the manual valve lever shaft.



    C137418
  1. Using a screwdriver, slide the spacer of the parking lock lever sub-assembly.



    C136702
  1. Using a pin punch (3 mm) and hammer, drive out the slotted spring pin from the parking lock lever sub-assembly.

    HINT:
    To prevent the pin from falling into the case, drive the pin until it has cleared the manual valve lever shaft.



    C137428
  1. Remove the manual valve lever shaft, manual valve lever sub-assembly, parking lock lever sub-assembly and 2 spacers from the transaxle case sub-assembly.



67. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    C136684
  1. Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case sub-assembly.