AUTOMATIC TRANSAXLE UNIT > REASSEMBLY |


| Mark | Front Race Diameter Inside / Outside [mm (in.)] | Thrust Bearing Diameter Inside / Outside [mm (in.)] | Rear Race Diameter Inside / Outside [mm (in.)] |
| A | - | 57.7 (2.27) / 75.2 (2.96) | - |
| B | - | 29.1 (1.15) / 48.6 (1.91) | 30.7 (1.21) / 48.3 (1.90) |
| C | - | 62.6 (2.46) / 82.4 (3.24) | 65.9 (2.59) / 82.3 (3.24) |
| D | 59.4 (2.34) / 76 (2.99) | 53.46 (2.10) / 79 (3.11) | - |
| E | - | 56.1 (2.21) / 81.1 (3.19) | - |
| F | - | 61.2 (2.41) / 79 (3.11) | - |
| G | - | 28 (1.10) / 47.1 (1.85) | 26.1 (1.03) / 44 (1.73) |
| H | 52.2 (2.06) / 70.4 (2.77) | 48.9 (1.93) / 72.0 (2.83) | - |
| 1. INSTALL COUNTER DRIVE GEAR BEARING |
![]() |
Using SST and a press, install a new counter drive gear bearing and snap ring to the transaxle case sub-assembly.
| 2. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL |
![]() |
Coat the lip of a new manual valve lever shaft oil seal with a small amount of MP grease.
Using SST and a hammer, tap in the manual valve lever shaft oil seal.
| 3. INSTALL MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY |
![]() |
Install the manual valve lever shaft sub-assembly to the transaxle case sub-assembly.
![]() |
Using needle-nose pliers, install the manual valve shaft retainer spring to the transaxle case sub-assembly.
| 4. INSTALL PARKING LOCK ROD SUB-ASSEMBLY |
![]() |
Align the slot with the notches on the manual valve lever shaft sub-assembly and install the parking lock rod sub-assembly.
| 5. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY |
![]() |
Install the manual detent spring sub-assembly and manual detent spring cover to the transaxle case sub-assembly with the bolt.
| 6. INSTALL NO. 3 BRAKE PISTON |
![]() |
Coat 2 new O-rings with ATF and install them to the No. 3 brake piston.
![]() |
Temporarily install the No. 3 brake piston to the transaxle case sub-assembly.
| *1 | No. 3 Brake Piston |
![]() |
Temporarily install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.
| *1 | No. 3 Brake Piston |
| *2 | Pawl Stopper Plate |
Press the No. 3 brake piston into the transaxle case sub-assembly.
Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.
![]() |
Install the brake piston return spring to the transaxle case sub-assembly.
| *1 | No. 3 Brake Piston |
| *2 | Brake Piston Return Spring |
![]() |
Place SST on the brake piston return spring and compress the brake piston return spring with a press.
| *1 | Snap Ring |
Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.
| 7. INSTALL COUNTER DRIVE GEAR |
![]() |
Using SST and a press, install a new counter drive gear bearing inner race (front side) to the counter drive gear.
![]() |
Using SST, install a new counter drive gear bearing inner race (rear side) and counter drive gear to the transaxle case sub-assembly.
| 8. INSTALL FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Using SST and a press, press in a new front planetary gear assembly to the transaxle case sub-assembly.
| 9. INSTALL NO. 2 BRAKE PISTON |
![]() |
Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.
![]() |
Install the No. 2 brake piston to the transaxle case sub-assembly.
| 10. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Install the 1st and reverse brake return spring to the transaxle case sub-assembly.
Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring with a press.
Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.
| 11. INSTALL NO. 2 BRAKE DISC |
![]() |
Install the 4 No. 2 brake discs, 4 No. 2 brake plates, and No. 2 brake flange to the transaxle case sub-assembly.
| *1 | No. 2 Brake Flange |
| *2 | No. 2 Brake Plate |
| *3 | No. 2 Brake Disc |
![]() |
Using a screwdriver, install the snap ring to the transaxle case sub-assembly.
| 12. INSPECT CLEARANCE OF NO. 2 BRAKE |
![]() |
Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Mark | Thickness [mm (in.)] |
| 40 | 4.0 (0.157) |
| 41 | 4.1 (0.161) |
| 42 | 4.2 (0.165) |
| 43 | 4.3 (0.169) |
| 44 | 4.4 (0.173) |
| 13. INSTALL PLANETARY RING GEAR FLANGE |
![]() |
Install the planetary ring gear flange to the planetary ring gear.
| *1 | Snap Ring |
| *2 | Planetary Ring Gear Flange |
| *3 | Planetary Ring Gear |
Using a screwdriver, install the snap ring to the planetary ring gear.
| 14. INSTALL ONE-WAY CLUTCH ASSEMBLY |
![]() |
Install the outer race retainer to the one-way clutch assembly.
| *1 | One-way Clutch Assembly |
| *2 | Outer Race Retainer |
| *3 | Planetary Ring Gear |
Install the one-way clutch assembly to the planetary ring gear.
![]() |
Coat the thrust needle roller bearing with ATF, and install it onto the front planetary gear assembly.
| *1 | Thrust Needle Roller Bearing |
| - | Inside [mm (in.)] | Outside [mm (in.)] |
| Bearing | 56.1 (2.21) | 81.1 (3.19) |
Install the one-way clutch assembly with the planetary ring gear to the transaxle case sub-assembly.
![]() |
Using a screwdriver, install the snap ring to the transaxle case sub-assembly.
| 15. INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (OUTER RACE) |
![]() |
Using SST and a hammer, install a new differential drive pinion tapered roller bearing LH (outer race) to the transaxle case sub-assembly.
| 16. INSTALL PARKING LOCK PAWL |
![]() |
Install the parking lock pawl to the transaxle case sub-assembly with the parking lock pawl shaft.
| *1 | Parking Lock Pawl Pin |
| *2 | Parking Lock Pawl Shaft |
| *3 | Spring |
| *4 | Parking Lock Pawl |
Install the parking lock pawl pin to the transaxle case sub-assembly.
![]() |
Install the torsion spring to the parking lock pawl.
| 17. INSTALL PARKING LOCK SLEEVE |
![]() |
Install the parking lock sleeve to the transaxle case sub-assembly.
| 18. INSTALL PAWL STOPPER PLATE |
![]() |
Install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.
| 19. INSTALL NO. 1 TRANSMISSION CASE PLATE |
![]() |
Clean and degrease the bolt and the installation hole in the transaxle case sub-assembly.
Apply adhesive to 2 or 3 threads on the ends of the bolt.
Install the No. 1 transmission case plate to the transaxle case sub-assembly with the bolt.
| 20. INSTALL PAWL SHAFT CLAMP |
![]() |
Install the pawl shaft clamp to the transaxle case sub-assembly with the bolt.
| 21. INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (INNER RACE) |
![]() |
Using SST and a press, install a new differential drive pinion tapered roller bearing RH (inner race) to the counter driven gear sub-assembly.
| 22. INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (INNER RACE) |
![]() |
Using SST and a press, install a new differential drive pinion tapered roller bearing LH (inner race) to the counter driven gear sub-assembly.
| 23. INSTALL COUNTER DRIVEN GEAR |
![]() |
Install the counter driven gear to the transaxle case sub-assembly.
| 24. INSTALL COUNTER DRIVE GEAR NUT |
![]() |
Turn the manual valve lever shaft counterclockwise to set it to the P position as shown in the illustration.
![]() |
Using SST, install a new counter drive gear nut.
![]() |
Turn the manual valve lever shaft 2 notches clockwise to set it to the N position as shown in the illustration.
![]() |
Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.
![]() |
Using SST and a hammer, stake the counter drive gear nut.
| 25. INSTALL FRONT DIFFERENTIAL CASE |
![]() |
Install the front differential case to the transaxle case sub-assembly.
| 26. INSTALL NO. 1 BRAKE PISTON |
![]() |
Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.
![]() |
Install the No. 1 brake piston to the front oil pump assembly.
| 27. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Install the 3 2nd brake piston return springs to the front oil pump assembly.
| 28. INSTALL NO. 1 BRAKE DISC |
![]() |
Install the 3 No. 1 brake discs, 3 No. 1 brake plates, and No. 1 brake flange to the front oil pump assembly.
| *1 | No. 1 Brake Flange |
| *2 | No. 1 Brake Plate |
| *3 | No. 1 Brake Disc |
![]() |
Place SST on the flange and compress the flange with a press.
Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration.
![]() |
Install the brake snap ring stopper to the front oil pump assembly.
![]() |
Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration.
![]() |
Check that the brake snap ring stopper can be turned by hand.
| *1 | Brake Snap Ring Stopper |
| *2 | Snap Ring |
| *a | Correctly Installed |
| 29. INSPECT CLEARANCE OF NO. 1 BRAKE |
![]() |
Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Mark | Thickness [mm (in.)] |
| 30 | 3.0 (0.118) |
| 31 | 3.1 (0.122) |
| 32 | 3.2 (0.126) |
| 33 | 3.3 (0.130) |
| 34 | 3.4 (0.134) |
| 35 | 3.5 (0.138) |
| 30. INSTALL UNDERDRIVE PLANETARY SUN GEAR |
![]() |
Coat the thrust needle roller bearing with ATF, and install it to the front oil pump assembly.
| *1 | Underdrive Planetary Sun Gear |
| *2 | Thrust Needle Roller Bearing |
| - | Inside [mm (in.)] | Outside [mm (in.)] |
| Bearing | 57.7 (2.27) | 75.2 (2.96) |
Install the underdrive planetary sun gear to the front oil pump assembly.
| 31. INSTALL INPUT SHAFT SUB-ASSEMBLY |
![]() |
Coat 3 new oil seal rings with ATF and install them to the input shaft sub-assembly.
| *1 | Thrust Bearing Race |
| *2 | Thrust Needle Roller Bearing |
| *3 | Input Shaft |
| *4 | Oil Seal Ring |
Coat the thrust needle roller bearing and thrust bearing race with ATF, and install them on the input shaft sub-assembly.
| - | Inside [mm (in.)] | Outside [mm (in.)] |
| Bearing | 29.1 (1.15) | 48.6 (1.91) |
| Race | 30.7 (1.21) | 48.3 (1.90) |
![]() |
Install the input shaft to the front oil pump assembly.
| 32. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY |
![]() |
Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.
| *1 | Planetary Sun Gear Sub-assembly |
| *2 | Underdrive Planetary Gear Assembly |
| *3 | Snap Ring |
Using a snap ring expander, install the planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.
| 33. INSTALL NO. 3 BRAKE HUB |
![]() |
Coat the thrust needle roller bearing with ATF and install it on the underdrive planetary gear assembly.
| *1 | Thrust Bearing Race |
| *2 | Thrust Needle Roller Bearing |
| - | Inside [mm (in.)] | Outside [mm (in.)] |
| Bearing | 62.6 (2.47) | 82.4 (3.24) |
| Race | 65.9 (2.59) | 82.3 (3.24) |
Coat the thrust bearing race with MP grease and install it to the No. 3 brake hub.
![]() |
Install the No. 3 brake hub to the underdrive planetary gear assembly.
| 34. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY |
![]() |
Install the underdrive planetary gear assembly to the front oil pump assembly.
| 35. INSTALL NO. 3 BRAKE DISC |
![]() |
Install the 2 No. 3 brake flanges, 3 No. 3 brake discs, and 2 No. 3 brake plates to the front oil pump assembly.
| *1 | No. 3 Brake Flange |
| *2 | No. 3 Brake Plate |
| *3 | No. 3 Brake Disc |
![]() |
Using a screwdriver, install the snap ring to the front oil pump assembly.
| 36. INSPECT CLEARANCE OF NO. 3 BRAKE |
![]() |
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the flange.
| *1 | Front Oil Pump Assembly |
| *2 | No. 3 Brake |
| *a | Dimension A |
| *b | Dimension B |
| *c | Contact Surface of Front Oil Pump Assembly |
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).
Calculate the clearance value using the following formula:
Clearance = Dimension B - Dimension A - Flange Thickness
| Mark | Thickness [mm (in.)] |
| 38 | 3.80 (0.150) |
| 39 | 3.90 (0.154) |
| 40 | 4.00 (0.157) |
| 41 | 4.10 (0.161) |
| 42 | 4.20 (0.165) |
| 43 | 4.30 (0.169) |
| 37. INSTALL FRONT OIL PUMP ASSEMBLY |
![]() |
Coat a new O-ring with ATF and install it to the transaxle case sub-assembly.
| *1 | Thrust Bearing Race |
| *2 | Thrust Needle Roller Bearing |
| *3 | O-ring |
Coat the thrust needle roller bearing and thrust bearing race with ATF and install them on the counter drive gear nut.
| - | Inside [mm (in.)] | Outside [mm (in.)] |
| Bearing | 53.46 (2.10) | 79 (3.11) |
| Race | 59.4 (2.34) | 76 (2.99) |
![]() |
Coat a new O-ring with ATF and install it to the front oil pump assembly.
![]() |
Install the front oil pump assembly to the transaxle case sub-assembly with the 7 bolts.
| *1 | O-ring |
Coat a new O-ring with ATF and install it to the front oil pump assembly.
| 38. INSTALL TRANSAXLE HOUSING OIL SEPARATOR |
![]() |
Clean and degrease the 3 bolts and the installation holes in the transaxle housing.
Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.
Install the transaxle housing oil separator to the transaxle housing with the 3 bolts.
| 39. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE |
![]() |
Install the differential gear lube apply tube to the transaxle housing.
Clean and degrease the bolt and the installation hole in the transaxle housing.
Apply adhesive to 2 or 3 threads on the ends of the bolt.
Install the apply tube clamp to the differential gear lube apply tube with the bolt.
| 40. INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (OUTER RACE) |
![]() |
Install the shim to the transaxle housing.
Using SST, install a new differential drive pinion tapered roller bearing RH (outer race) to the transaxle housing.
| 41. ADJUST COUNTER DRIVEN GEAR PRELOAD |
![]() |
Remove packing material from the contact surfaces between the transaxle housing and transaxle case sub-assembly.
Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.
![]() |
Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.
| Thickness | Thickness | Thickness | Thickness |
| 2.000 (0.0787) | 2.275 (0.0896) | 2.550 (0.100) | 2.825 (0.111) |
| 2.025 (0.0797) | 2.300 (0.0906) | 2.575 (0.101) | 2.850 (0.112) |
| 2.050 (0.0807) | 2.325 (0.0915) | 2.600 (0.102) | 2.875 (0.113) |
| 2.075 (0.0817) | 2.350 (0.0925) | 2.625 (0.103) | 2.900 (0.114) |
| 2.100 (0.0827) | 2.375 (0.0935) | 2.650 (0.104) | 2.925 (0.115) |
| 2.125 (0.0837) | 2.400 (0.0945) | 2.675 (0.105) | 2.950 (0.116) |
| 2.150 (0.0846) | 2.425 (0.0955) | 2.700 (0.106) | 2.975 (0.117) |
| 2.175 (0.0856) | 2.450 (0.0965) | 2.725 (0.107) | 3.000 (0.118) |
| 2.200 (0.0866) | 2.475 (0.0974) | 2.750 (0.108) | - |
| 2.225 (0.0876) | 2.500 (0.0984) | 2.775 (0.109) | - |
| 2.250 (0.0886) | 2.525 (0.0994) | 2.800 (0.110) | - |
![]() |
Remove the 20 bolts and the transaxle housing.
| 42. INSTALL TRANSAXLE HOUSING |
![]() |
Clean and degrease the contact surfaces between the transaxle housing and transaxle case sub-assembly.
Apply FIPG to the transaxle case sub-assembly.
![]() |
Install the transaxle housing to the transaxle case sub-assembly with the 17 bolts.
![]() |
Clean and degrease the 3 bolts and the installation holes in the automatic transaxle assembly.
Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.
Install the 3 bolts.
| 43. INSPECT CLEARANCE OF NO. 1 CLUTCH |
![]() |
Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.
Check that the piston moves when compressed air (200 kPa, 2.0 kgf/cm2, 29 psi) is applied to the oil hole.
![]() |
Using a feeler gauge, measure the No. 1 clutch pack clearance.
| *1 | Feeler Gauge |
| 44. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY |
![]() |
Coat the thrust needle roller bearing and thrust bearing race with ATF, and install them to the direct multiple disc clutch assembly.
| *1 | Thrust Needle Roller Bearing |
| *2 | Thrust Bearing Race |
| - | Inside [mm (in.)] | Outside [mm (in.)] |
| Bearing | 28 (1.10) | 47.1 (1.85) |
| Race | 26.1 (1.03) | 44 (1.73) |
![]() |
Install the rear planetary sun gear assembly to the direct multiple disc clutch assembly.
| *1 | Rear Planetary Sun Gear |
![]() |
Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.
![]() |
Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.
| *1 | O-ring |
| *2 | Oil Seal Ring |
Coat a new oil seal ring with ATF and install it to the intermediate shaft.
| 45. INSPECT CLEARANCE OF NO. 2 CLUTCH |
![]() |
Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.
Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| 46. INSTALL REAR MULTIPLE DISC CLUTCH ASSEMBLY |
![]() |
Coat the rear thrust needle roller bearing with ATF and install it on the transaxle case sub-assembly.
| *1 | Thrust Needle Roller Bearing |
| *2 | Rear Multiple Disc Clutch Assembly |
| - | Inside [mm (in.)] | Outside [mm (in.)] |
| Bearing | 61.2 (2.41) | 79 (3.11) |
Install the direct multiple disc clutch assembly to the transaxle case sub-assembly.
| 47. INSPECT INTERMEDIATE SHAFT END PLAY |
![]() |
Clean the contact surfaces of the transaxle case sub-assembly and rear transaxle cover sub-assembly.
As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case sub-assembly and the straightedge using a vernier caliper (Dimension A).
| *a | Dimension A |
![]() |
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).
| *a | Dimension B |
Calculate the end play value using the following formula:
End play = Dimension B - Dimension A - Thrust needle roller bearing thickness
| 48. INSTALL REAR TRANSAXLE COVER SUB-ASSEMBLY |
![]() |
Using SST and a hammer, install a new needle roller bearing into the rear transaxle cover sub-assembly.
![]() |
Clean and degrease the 2 "TORX" screws and the installation holes in the rear transaxle cover sub-assembly.
Apply adhesive to 2 or 3 threads on the ends of the 2 "TORX" screws.
Using a T30 "TORX" socket wrench, install the rear transaxle cover plate to the rear transaxle cover sub-assembly with the 2 "TORX" screws.
![]() |
Coat the thrust needle roller bearing and thrust bearing race with ATF and install them on the rear transaxle cover sub-assembly.
| *1 | Oil Seal Ring |
| *2 | Thrust Needle Roller Bearing |
| *3 | Thrust Bearing Race |
| - | Inside [mm (in.)] | Outside [mm (in.)] |
| Bearing | 48.9 (1.93) | 72.0 (2.83) |
| Race | 52.2 (2.06) | 70.4 (2.77) |
Coat 2 new oil seal rings with ATF and install them to the rear transaxle cover sub-assembly.
![]() |
Coat 3 new O-rings with ATF and install them to the transaxle case sub-assembly.
![]() |
Remove packing material from the contact surfaces between the rear transaxle cover sub-assembly and transaxle case sub-assembly.
Apply FIPG to the transaxle case sub-assembly.
![]() |
Install the rear transaxle cover sub-assembly to the transaxle case sub-assembly with the 12 bolts.
![]() |
Clean and degrease the 2 bolts and the installation holes in the transaxle case sub-assembly.
Apply adhesive to 2 or 3 threads on the ends of the 2 bolts.
Install the 2 bolts.
| 49. INSTALL REAR TRANSAXLE COVER PLUG |
![]() |
Coat 3 new O-rings with ATF and install them to the 3 rear transaxle cover plugs.
Install the 3 rear transaxle cover plugs to the rear transaxle cover sub-assembly.
| 50. INSTALL REFILL PLUG |
![]() |
Install a new gasket to the refill plug.
Install the refill plug to the rear transaxle cover sub-assembly.
| 51. INSPECT INPUT SHAFT END PLAY |
![]() |
Using a dial indicator, measure the input shaft end play.
| 52. INSTALL NO. 1 GOVERNOR APPLY GASKET |
![]() |
Coat 2 new No. 1 governor apply gaskets with ATF.
Install the 2 No. 1 governor apply gaskets onto the transaxle case sub-assembly.
| 53. INSTALL TRANSMISSION VALVE BODY ASSEMBLY |
![]() |
Coat the O-ring of the transmission wire with ATF.
Insert the pin of the manual valve lever into the groove on the end of the manual valve and install the transmission valve body assembly onto the automatic transaxle assembly with the 11 bolts.
| *a | Positioning Bolt |
| Bolt | Length [mm (in.)] |
| A | 25 (0.984) |
| B | 30 (1.18) |
| C and D | 35 (1.38) |
| 54. INSTALL VALVE BODY OIL STRAINER ASSEMBLY |
![]() |
Coat a new O-ring with ATF.
Install the O-ring onto the valve body oil strainer assembly.
![]() |
Install the valve body oil strainer assembly onto the transmission valve body assembly with the 2 bolts.
| 55. INSTALL TRANSMISSION OIL CLEANER MAGNET |
![]() |
Install the 2 transmission oil cleaner magnets onto the automatic transaxle oil pan sub-assembly as shown in the illustration.
| *1 | Transmission Oil Cleaner Magnet |
| 56. INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET |
Install a new automatic transaxle oil pan gasket onto the automatic transaxle oil pan sub-assembly.
| 57. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY |
![]() |
Install the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket onto the automatic transaxle assembly with the 17 bolts.
![]() |
Clean and degrease the 2 bolts and the installation holes in the transaxle case sub-assembly.
Apply adhesive to 2 or 3 threads on the ends of the bolt.
Install the 2 bolts.
| 58. INSTALL NO. 1 TRANSMISSION OIL FILLER TUBE |
![]() |
Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.
| 59. INSTALL OVERFLOW PLUG |
![]() |
Using a 6 mm hexagon socket wrench, install the overflow plug and a new gasket to the automatic transaxle oil pan sub-assembly.
| 60. INSTALL NO. 2 TRANSAXLE CASE PLUG |
![]() |
Clean and degrease the 3 No. 2 transaxle case plugs and the installation holes in the transaxle housing.
Apply adhesive to 2 or 3 threads on the ends of the 3 No. 2 transaxle case plugs.
Install the 3 new gaskets to the 3 No. 2 transaxle case plugs.
Using a 6 mm hexagon socket wrench, install the 3 No. 2 transaxle case plugs to the transaxle housing with the gaskets.
| 61. INSTALL NO. 1 TRANSAXLE CASE PLUG |
![]() |
Coat 3 new O-rings with ATF and install them to the 3 No. 1 transaxle case plugs.
Install the 3 No. 1 transaxle case plugs to the transaxle case sub-assembly.
| 62. INSTALL OIL COOLER TUBE UNION (INLET) |
![]() |
Coat a new O-ring with ATF and install it to the oil cooler tube union (inlet).
Install the oil cooler tube union (inlet) to the transaxle case sub-assembly as shown in the illustration.
| 63. INSTALL OIL COOLER TUBE UNION (OUTLET) |
![]() |
Coat a new O-ring with ATF and install it to the oil cooler tube union (outlet).
Install the oil cooler tube union (outlet) to the transaxle case sub-assembly.
| 64. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.
![]() |
Align the protrusions of the park/neutral position switch assembly as shown in the illustration.
| *1 | Protrusion |
Tighten the 2 bolts
| 65. INSTALL TRANSMISSION CONTROL SHAFT LEVER |
![]() |
Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the washer and nut.
| 66. INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY |
![]() |
Coat a new O-ring with ATF and install it to the No. 2 breather plug.
| *1 | No. 1 Breather Plug |
| *2 | Breather Plug Hose |
| *3 | No. 2 Breather Plug |
| *4 | O-ring |
Install the No. 2 breather plug to the breather plug hose.
Install the No. 1 breather plug to the breather plug hose.
![]() |
Install the transmission breather plug hose sub-assembly to the transaxle case sub-assembly.
| *1 | No. 2 Breather Plug |
| *a | Boss |