Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System)

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

  1. w/o Wireless Door Lock Buzzer Answer Back Function:
    When there are communication malfunctions between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.
  2. w/o Wireless Door Lock Buzzer Answer Back Function:
    When there are communication malfunctions between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
Either condition is met (1 trip detection logic*4):
  1. A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.
  2. A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.
  1. ID code box (immobiliser code ECU)*1
  2. Certification ECU (smart key ECU assembly)*2
  3. ECM
  4. Telephone transceiver assembly*3
  5. Wire harness or connector
Either condition is met:
  1. Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, the engine switch is pressed while carrying the key). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).
  2. 10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).
  1. *1: w/o Wireless Door Lock Buzzer Answer Back Function
  2. *2: w/ Wireless Door Lock Buzzer Answer Back Function
  3. *3: w/ Blocking System
  4. *4: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B2799
-

WIRING DIAGRAM


w/o Blocking System

B278902E01


w/ Blocking System

B278903E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or telephone transceiver assembly*, refer to the Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  3. When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.*

  1. *: w/ Blocking System

HINT:
When DTC B2799 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

1.SYSTEM CHECK
  1. Check the vehicle specification.

    Result:
    Result
    Proceed to
    w/o Blocking System
    A
    w/ Blocking System
    B



B
Go to step 6
A


2.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU)*3 OR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)*4 - ECM)
  1. Disconnect the A25 ECM connector.

  1. Disconnect the I20 ID code box (immobiliser code ECU) connector.*3

  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.*4

    1. *3: w/o Wireless Door Lock Buzzer Answer Back Function
    2. *4: w/ Wireless Door Lock Buzzer Answer Back Function

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-3 (EFII) - A25-30 (IMO)*3
    A43-14 (EFII) - A25-30 (IMO)*4
    Always
    Below 1 Ω
    A25-30 (IMO) - Body ground
    Always
    10 kΩ or higher
    I20-4 (EFIO) - A25-31 (IMI)*3
    A43-13 (EFIO) - A25-31 (IMI)*4
    Always
    Below 1 Ω
    A25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-3 (EFII) - A25-29 (IMO)*3
    A43-14 (EFII) - A25-29 (IMO)*4
    Always
    Below 1 Ω
    A25-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    I20-4 (EFIO) - A25-28 (IMI)*3
    I20-13 (EFIO) - A25-28 (IMI)*4
    Always
    Below 1 Ω
    A25-28 (IMI) - Body ground
    Always
    10 kΩ or higher

    1. *3: w/o Wireless Door Lock Buzzer Answer Back Function
    2. *4: w/ Wireless Door Lock Buzzer Answer Back Function



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


4.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


5.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.



NG
Go to step 15
OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED) 

6.CHECK HARNESS AND CONNECTOR (ECM - TELEPHONE TRANSCEIVER ASSEMBLY)
  1. Disconnect the A25 ECM connector.

  1. Disconnect the I70 telephone transceiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I70-8 (BLK3) - A25-31 (IMI)
    Always
    Below 1 Ω
    A25-30 (IMO) - Body ground
    Always
    10 kΩ or higher
    I70-7 (BLK2) - A25-30 (IMO)
    Always
    Below 1 Ω
    A25-31 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - TELEPHONE TRANSCEIVER ASSEMBLY)
  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I70-1 (BLK1) - A43-14 (EFII)
    Always
    Below 1 Ω
    A43-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    I70-2 (BLK4) - A43-13 (EFIO)
    Always
    Below 1 Ω
    A43-14 (EFII) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.ECU COMMUNICATION ID REGISTRATION
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


9.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


10.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.



NG
Go to step 11
OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED) 

11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
  1. Temporarily replace the telephone transceiver assembly with a new or known good one.

    HINT:
    Refer to the Service Bulletin.


NEXT


12.ECU COMMUNICATION ID REGISTRATION
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


13.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


14.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.



NG
Go to step 15
OK

END (TELEPHONE TRANSCEIVER ASSEMBLY WAS DEFECTIVE) 

15.REPLACE ECM
  1. Temporarily replace the ECM with a new or known good one (Click here for 2GR-FE, Click here for 2AR-FE).


NEXT


16.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


17.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/o Wireless Door Lock Buzzer Answer Back Function)
    B
    NG (w/ Wireless Door Lock Buzzer Answer Back Function)
    C



B
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

C
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
A

END (ECM WAS DEFECTIVE)