DTC C1237 Speed Sensor Rotor Faulty |
DTC C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1237 | Any of the following is detected:
|
|
| C1275 C1276 | Detected only during Test Mode. | Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH) |
| C1277 C1278 | Detected only during Test Mode. | Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (SPEED SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Check the speed value output from the speed sensor displayed on the intelligent tester.
| Result | Proceed to |
| OK | A |
| NG (for front) | B |
| NG (for rear) | C |
|
| ||||
|
| ||||
| A | |
| 3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check using the Test Mode procedure (Click here).
| Result | Proceed to |
| OK | A |
| NG (for front) | B |
| NG (for rear) | C |
|
| ||||
|
| ||||
| A | |
| 4.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is not output. | A |
| DTC C1237 is output (for front). | B |
| DTC C1237 is output (for rear). | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR |
Remove the front speed sensor and the component with the sensor rotor (Click here for speed sensor, Click here 2GR-FE for sensor rotor, Click here 2AR-FE for sensor rotor, and/or Click here 1AZ-FE for sensor rotor).
Check the speed sensor tip and speed sensor rotor.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Install the front speed sensor and the component with the sensor rotor.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-16 (FR+) - A53-1 (FR+) | Always | Below 1 Ω |
| A49-16 (FR+) - Body ground | Always | 10 kΩ or higher |
| A49-4 (FR-) - A53-2 (FR-) | Always | Below 1 Ω |
| A49-4 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A49-19 (FL+) - A16-1 (FL+) | Always | Below 1 Ω |
| A49-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A49-8 (FL-) - A16-2 (FL-) | Always | Below 1 Ω |
| A49-8 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.RECONFIRM DTC |
Reconnect the skid control ECU connector and the front speed sensor connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | |
| 8.REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 9.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | |
| 10.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY |
Turn the ignition switch off.
Replace the front speed sensor rotor (front drive outboard joint shaft assembly) (Click here for 2GR-FE, Click here for 2AR-FE, or Click here for 1AZ-FE).
| NEXT | |
| 11.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | ||
| ||
| 12.INSPECT SKID CONTROL SENSOR WIRE |
![]() |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Remove the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| h1-2 (RR+) - hO1-1 (RR+) | Always | Below 1 Ω |
| h1-2 (RR+) - hO1-2 (RR-) | Always | 10 kΩ or higher |
| h1-2 (RR+) - Body ground | Always | 10 kΩ or higher |
| h1-1 (RR-) - hO1-2 (RR-) | Always | Below 1 Ω |
| h1-1 (RR-) - hO1-1 (RR+) | Always | 10 kΩ or higher |
| h1-1 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| i1-2 (RL+) - iN1-1 (RL+) | Always | Below 1 Ω |
| i1-2 (RL+) - iN1-2 (RL-) | Always | 10 kΩ or higher |
| i1-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| i1-1 (RL-) - iN1-2 (RL-) | Always | Below 1 Ω |
| i1-1 (RL-) - iN1-1 (RL+) | Always | 10 kΩ or higher |
| i1-1 (RL-) - Body ground | Always | 10 kΩ or higher |
| *A | for RH |
| *B | for LH |
| *a | Front view of skid control sensor wire |
| *b | Front view of wire harness connector (to Sensor Side Connector) |
| *c | Front view of wire harness connector (to Vehicle Side Connector) |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-17 (RR+) - hO1-1 (RR+) | Always | Below 1 Ω |
| A49-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A49-29 (RR-) - hO1-2 (RR-) | Always | Below 1 Ω |
| A49-29 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A49-31 (RL+) - iN1-1 (RL+) | Always | Below 1 Ω |
| A49-31 (RL+) - Body ground | Always | 10 kΩ or higher |
| A49-18 (RL-) - iN1-2 (RL-) | Always | Below 1 Ω |
| A49-18 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 14.RECONFIRM DTC |
Install the skid control sensor wire.
Reconnect the skid control ECU connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | |
| 15.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY |
Turn the ignition switch off.
Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly) (Click here).
| NEXT | |
| 16.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
|
| ||||
| A | ||
| ||