Home › Engine / Hybrid System ยท 1AZ-FE › INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR
  1. Install the No. 1 manifold converter insulator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



2. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 2 exhaust manifold heat insulator with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



3. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Set a new exhaust manifold to head gasket to the cylinder head sub-assembly.

  1. Temporarily install the exhaust manifold converter sub-assembly with the 5 nuts.

  1. Temporarily install the No. 2 manifold stay and manifold stay with the 2 bolts and 2 nuts.



    A195979E05
  1. Using a 12 mm deep socket wrench, install the exhaust manifold converter sub-assembly and 5 nuts in the order shown in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



4. INSTALL NO. 2 MANIFOLD STAY
  1. Install the No. 2 manifold stay with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



5. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



6. INSTALL AIR FUEL RATIO SENSOR


    A264430E01
  1. Using SST, install the air fuel ratio sensor to the exhaust manifold converter sub-assembly.
    Text in Illustration 
    *a
    Fulcrum Length
    30 mm
    *b
    Fulcrum Length
    300 mm

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 448 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.) and a torque wrench with a fulcrum length of 300 mm (11.8 in.) (Click here).
    2. The "with SST" torque value is effective when SST is parallel to the torque wrench.

  1. Connect the air fuel ratio sensor connector.

  1. Install the hose clamp.



7. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 1 exhaust manifold heat insulator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum
    40.5 mm (1.59 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Fully insert a new gasket to the exhaust manifold converter sub-assembly.



    A181728E15
  1. Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly
    *2
    Gasket
    *3
    Wooden Block

    NOTICE:
    1. Be sure to install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Install a new gasket to the front exhaust pipe assembly.

  1. Install the front exhaust pipe assembly with the 2 bolts, 2 nuts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the oxygen sensor connector.



9. INSTALL ENGINE UNDER COVER RH


10. INSTALL ENGINE UNDER COVER LH


11. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH


12. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH


13. INSPECT FOR EXHAUST GAS LEAK