Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1500    Fuel Sender Open Detected

for Preparation Click here


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.

DTC No.
DTC Detection Condition
Trouble Area
B1500
When IG voltage is 9.5 V or more and the following condition is detected:
  1. Fuel sender gauge operation malfunction
  1. Harness or connector
  2. Fuel sender gauge assembly
  3. Combination meter assembly

WIRING DIAGRAM


E156126E40


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input signal/Min.: 0, Max.: 127.5
    Fuel receiver gauge indicates F: 57.0
    Unit: Liter
    Fuel receiver gauge indicates 3/4: 48.3
    Fuel receiver gauge indicates 1/2: 32.2
    Fuel receiver gauge indicates 1/4: 16.1
    Fuel receiver gauge indicates E: 6.4

    Result:

    Result
    Proceed to
    Fuel level data can be displayed on the intelligent tester and DTC B1500 is output.
    A
    Fuel level data cannot be displayed on the intelligent tester.
    B



B
Go to step 2
A

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.INSPECT FUEL SENDER GAUGE ASSEMBLY


    E224284E05
  1. Disconnect the I18 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-18 (FR) - I18-17 (FE)
    Always
    13.5 to 414.5 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
  1. Disconnect the N11 fuel suction tube assembly with pump and gauge connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-18 (FR) - N11-2 (FS)
    Always
    Below 1 Ω
    I18-18 (FR) - Body ground
    Always
    10 kΩ or higher
    I18-17 (FE) - N11-3 (FE)
    Always
    Below 1 Ω
    I18-17 (FE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FUEL SENDER GAUGE ASSEMBLY
E224291E01
  1. Remove the fuel sender gauge assembly (Click here for 2AR-FE, Click here for 2GR-FE).

  1. Check that the float moves smoothly between E and F.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    13.5 to 16.5 Ω
    1 - 2
    Float level is between F (upper) and E (lower)
    13.5 to 414.5 Ω (Gradually changes)
    1 - 2
    Float level is E (lower)
    405.5 to 414.5 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2AR-FE)
    B
    NG (for 2GR-FE)
    C

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Sender Gauge Assembly)



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (for 2AR-FE) (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (for 2GR-FE) (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)