Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No.
DTC Detection Condition
Trouble Area
B279A
Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
  1. Wire harness or connector
  2. ECM
  3. Transponder key ECU assembly

WIRING DIAGRAM


B203372E51


INSPECTION PROCEDURE

NOTICE:
If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

1.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If any DTCs other than DTC B279A are output, troubleshoot those DTCs first.

    Result:
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
  1. Disconnect the transponder key ECU assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-13 (EFIO) - A25-28 (IMI)
    Always
    Below 1 Ω
    I19-13 (EFIO) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I19-13 (EFIO) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)
  1. Reconnect the transponder key ECU assembly connector.

  1. Reconnect the ECM connector.



  1. Using an oscilloscope, check the waveform.


    B278949E01

    Waveform (Reference):
    Item
    Content
    Terminal No. (Symbol)
    I19-13 (EFIO) - I19-16 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Within 3 seconds of engine start or within 3 seconds of ignition switch turned ON after battery cable disconnected and reconnected

    OK:
    Waveform is output normally (see illustration).


    Text in Illustration 
    *a
    Component with harness connected
    (Transponder Key ECU Assembly)
    *b
    GND
    *c
    Waveform
    *d
    High
    *e
    Low
    -
    -



NG
Go to step 4
OK

REPLACE ECM (Click here)  

4.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly.

    HINT:
    Refer to Service Bulletin.


NEXT


5.REGISTER KEY
  1. Register the key.

    HINT:
    Refer to Service Bulletin.


NEXT


6.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


7.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    DTC B279A is not output.



NG
REPLACE ECM (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)