SMART ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Unlock Function does not Operate |

| 1.CHECK POWER DOOR LOCK CONTROL SYSTEM |
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (UNLOCK DETECTION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FL Door Lock Pos*1 | Front LH door unlock detection switch signal / UNLOCK or LOCK | UNLOCK: Front LH door unlocked LOCK: Front LH door locked | - |
| FR Door Lock Pos*2 | Front RH door unlock detection switch signal / UNLOCK or LOCK | UNLOCK: Front RH door unlocked LOCK: Front RH door locked | - |
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (UNLOCK SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry & Start or Main Body / Data List.
Turn the intelligent tester on.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D-Door Touch Sensor | Driver door touch sensor (unlock sensor) / ON or OFF | ON: Driver door touch sensor (unlock sensor) touched OFF: Driver door touch sensor (unlock sensor) not touched |
|
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU) |
Disconnect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.
Disconnect the I78 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1-4 (SENS) - I78-22 (SEN1) | Always | Below 1 Ω |
| A43-11 (E) - Body ground | Always | Below 1 Ω |
| W1-4 (SENS) or I78-22 (SEN1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| V1-4 (SENS) - I78-22 (SEN1) | Always | Below 1 Ω |
| A43-11 (E) - Body ground | Always | Below 1 Ω |
| V1-4 (SENS) or I78-22 (SEN1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (DRIVER DOOR UNLOCK SENSOR SIGNAL INPUT) |
Connect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.

| *1 | Waveform | - | - |
| *a | Component with harness connected (Certification ECU (smart key ECU assembly)) | *b | In actuality, sampling is being performed |
Connect the I78 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
| I78-22 (SEN1) - A43-11 (E) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
|
| ||||
| OK | ||
| ||