BRAKE BOOSTER (for RHD) > INSTALLATION |
| 1. INSTALL CHECK VALVE GROMMET |
Install a new check valve grommet to the brake booster assembly.
| 2. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY |
Install the brake vacuum check valve assembly to the brake booster assembly.
| 3. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.
![]() |
Set the push rod length as shown in the illustration.
| *1 | Lock Nut |
| *2 | Brake Master Cylinder Push Rod Clevis |
| *a | Push Rod Length |
Tighten the lock nut.
| 4. INSTALL BRAKE BOOSTER GASKET |
Install a new brake booster gasket to the brake booster assembly.
| 5. INSTALL BRAKE BOOSTER ASSEMBLY |
Install the brake booster assembly to the vehicle body with the 4 nuts.
| 6. INSTALL PUSH ROD PIN |
![]() |
Apply lithium soap base glycol grease to the push rod pin.
![]() | Lithium Soap Base Glycol Grease |
Connect the brake master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.
| 7. CONNECT UNION TO CHECK VALVE HOSE |
Connect the union to check valve hose to the brake booster assembly, and slide the clip to secure it.
| 8. INSTALL VACUUM SWITCHING VALVE ASSEMBLY |
Install the vacuum switching valve assembly with the bolt.
Connect the 2 vacuum hoses and connector.
Connect the union to check valve hose and wire harness clamp.
| 9. CONNECT BRAKE LINE |
![]() |
Install 2 new clamps to the brake lines.
Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.
| 10. INSTALL NO. 1 BRAKE TUBE CLAMP |
![]() |
Install a new No. 1 brake tube clamp to the vehicle body.
Engage the brake lines to the clamp.
| 11. INSTALL SUCTION PIPE SUB-ASSEMBLY |
Remove the attached vinyl tape from the openings of the disconnected parts.
Sufficiently apply compressor oil to a new O-ring, fitting surface of the suction pipe sub-assembly and air conditioning unit.
Install the O-ring on the suction pipe sub-assembly.
![]() |
Insert the suction pipe sub-assembly to the air conditioning unit.
![]() |
Install the clamp with suction pipe sub-assembly and air conditioning tube and accessory assembly to the No. 1 brake tube clamp.
![]() |
Install the clamp to the brake actuator bracket assembly.
| 12. INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY |
Remove the attached vinyl tape from the openings of the disconnected parts.
Sufficiently apply compressor oil to 2 new O-rings, the fitting surface of the air conditioning tube and accessory assembly, cooler condenser assembly and air conditioning unit.
Install the 2 O-rings on the air conditioning tube and accessory assembly.
Insert the air conditioning tube and accessory assembly to the cooler condenser assembly.
Install the bolt.
![]() |
Insert the air conditioning tube and accessory assembly to the air conditioning unit.
Turn the hook connector and install the bolt.
![]() |
Install the clamp to the vehicle body and connect the pressure sensor connector.
| 13. INSTALL RADIATOR SIDE DEFLECTOR RH |
Engage the guide and 3 claws to install the radiator side deflector RH.
| 14. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY |
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 16. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100 g (3.5 oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| 17. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 18. INSPECT FOR REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 19. INSTALL FRONT BUMPER COVER |
| 20. INSPECT AND ADJUST BRAKE PEDAL |