Home › Engine / Hybrid System ยท 2AR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > INSPECTION

for Preparation Click here



1. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY


    A160725
  1. Turn the roller by hand to check that it turns smoothly.
    If the roller does not turn smoothly, replace the valve rocker arm sub-assembly.



2. INSPECT VALVE LASH ADJUSTER ASSEMBLY


A186391E02

NOTICE:
  1. Keep the adjuster free from dirt and foreign matter.
  2. Use only clean engine oil.

Text in Illustration 
*1
Plunger
*2
Check Ball
*a
CORRECT
*b
INCORRECT
*c
Taper Part
*d
Low Pressure Chamber
*e
High Pressure Chamber
  1. Place the lash adjuster into a container full of new engine oil.

  1. Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

    SST
    09276-75010  

  1. Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed the air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the valve lash adjuster assembly.



3. INSPECT CAMSHAFT OIL CLEARANCE

NOTICE:
Do not turn the camshafts.

  1. Clean the bearing caps, camshaft housing and camshaft journals.

  1. Place the camshafts on the camshaft housing.



    A194965E04
  1. Lay a strip of Plastigage across each of the camshaft journals.
    Text in Illustration 
    *1
    Plastigage

  1. Install the camshaft bearing caps .

  1. Install the camshaft housing sub-assembly .

  1. Remove the camshaft bearing caps .



    A194966E04
  1. Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Item
    Specified Condition
    Intake No. 1 journal
    0.035 to 0.072 mm (0.00137 to 0.00283 in.)
    Exhaust No. 1 journal
    0.049 to 0.086 mm (0.00193 to 0.00339 in.)
    Other journal
    0.025 to 0.062 mm (0.000984 to 0.00244 in.)

    Maximum Oil Clearance:
    Item
    Specified Condition
    Intake No. 1 journal
    0.085 mm (0.00335 in.)
    Exhaust No. 1 journal
    0.095 mm (0.00374 in.)
    Other journal
    0.085 mm (0.00335 in.)

    Text in Illustration 
    *1
    Plastigage
    *2
    No. 1 Journal
    *3
    Other Journal
    If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing.



4. INSPECT CAMSHAFT THRUST CLEARANCE
  1. Clean the bearing caps, camshaft housing and camshaft journals.

  1. Place the camshafts on the camshaft housing.

  1. Install the camshaft bearing caps .

  1. Install the camshaft housing sub-assembly .



    A194962
  1. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard Thrust Clearance:
    Item
    Specified Condition
    Intake
    0.060 to 0.155 mm (0.00236 to 0.00610 in.)
    Exhaust
    0.060 to 0.155 mm (0.00236 to 0.00610 in.)

    Maximum Thrust Clearance:
    Item
    Specified Condition
    Intake
    0.170 mm (0.00669 in.)
    Exhaust
    0.170 mm (0.00669 in.)

    If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.



5. INSPECT CAMSHAFT


    A196939
  1. Inspect the camshaft runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.00118 in.)

      If the circle runout is more than the maximum, replace the camshaft.

      HINT:
      Check the oil clearance after replacing the camshaft.



    A196940
  1. Inspect the cam lobes.

    1. Using a micrometer, measure the cam lobe height.

      Standard Cam Lobe Height:
      Item
      Specified Condition
      Intake
      44.163 to 44.305 mm (1.739 to 1.744 in.)
      Exhaust
      44.144 to 44.286 mm (1.738 to 1.744 in.)

      Minimum Cam Lobe Height:
      Item
      Specified Condition
      Intake
      44.013 mm (1.733 in.)
      Exhaust
      43.996 mm (1.732 in.)

      If the cam lobe height is less than the minimum, replace the camshaft sub-assembly.



    A196941
  1. Inspect the camshaft journals.

    1. Using a micrometer, measure the journal diameter.

      Standard Journal Diameter:
      Item
      Specified Condition
      No. 1 journal
      34.449 to 34.465 mm (1.356 to 1.357 in.)
      Other journals
      22.959 to 22.975 mm (0.904 to 0.905 in.)

      If the journal diameter is not as specified, check the oil clearance .



6. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY


    A196901E02
  1. Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Knock Pin



    A196904E11
  1. Check that there is no clearance between the camshaft timing gear and camshaft flange.
    Text in Illustration 
    *1
    Camshaft Timing Gear
    *2
    Flange
    *a
    INCORRECT
    *b
    CORRECT
    *c
    Clearance
    *d
    No Clearance

  1. Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing gear by hand.

    NOTICE:
    Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.

  1. Check the lock of the camshaft timing gear.

    1. Make sure that the camshaft timing gear is locked.

      NOTICE:
      Be careful not to damage the camshaft.



    A196905E05
  1. Release the lock pin.
    Text in Illustration 
    *1
    Rubber
    *2
    Vinyl Tape
    *3
    Knock Pin
    *a
    Retard Side Path
    *b
    Advance Side Path
    *c
    Open
    *d
    Close

    1. Clean the camshaft journal with non-residue solvent.

    2. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      There are 4 oil paths in the grooves of the camshaft. Plug three of the paths with pieces of rubber.

    3. Open a hole at port A shown in the illustration.



    4. A196906
    5. While applying approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the oil path, forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

      CAUTION:
      Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.

      NOTICE:
      Do not allow the camshaft timing gear assembly to lock. If it locks, release the lock pin again.

      HINT:
      1. The camshaft timing gear assembly may be turned in the advance direction without applying any force.
      2. If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.

  1. Check for smooth rotation.

    1. Turn the camshaft timing gear within its movable range (26.5 to 28.5°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

      NOTICE:
      Do not allow the camshaft timing gear assembly to lock.
      If it locks, release the lock pin again.

  1. Remove the vinyl tape and rubber pieces from the camshaft.

  1. Remove the bolt and camshaft timing gear.



7. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY


    A196902E05
  1. Align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Knock Pin



    A196904E11
  1. Check that there is no clearance between the camshaft timing exhaust gear and camshaft flange.
    Text in Illustration 
    *1
    Camshaft Timing Exhaust Gear
    *2
    Flange
    *a
    INCORRECT
    *b
    CORRECT
    *c
    Clearance
    *d
    No Clearance

  1. Secure the camshaft in place by hand, and then install the installation bolt of the camshaft timing exhaust gear by hand.

  1. Check the lock of the camshaft timing exhaust gear.

    1. Make sure that the camshaft timing exhaust gear is locked.

      NOTICE:
      Be careful not to damage the camshaft.



    A196942E03
  1. Release the lock pin.
    Text in Illustration 
    *1
    Vinyl Tape
    *2
    Rubber
    *3
    Knock Pin
    *a
    Retard Side Path
    *b
    Advance Side Path
    *c
    Open
    *d
    Close

    1. Clean the camshaft journal with non-residue solvent.

    2. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      There are 4 oil paths in the grooves of the camshaft. Plug 2 paths with rubber pieces.

    3. Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.



    4. A198157E04
    5. Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the two open paths (the advance side path and retard side path).
      Text in Illustration 
      *1
      Retard Side Path
      *2
      Advance Side Path

      NOTICE:
      Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.



    6. A198158E04
    7. Check that the camshaft timing exhaust gear turns in the retard direction when reducing the air pressure applied to the advance side path.
      Text in Illustration 
      *1
      Retard Side Path
      *2
      Advance Side Path
      *3
      Hold Pressure
      *4
      Decompress

      HINT:
      The lock pin is released and the camshaft timing exhaust gear turns in the retard direction.

    8. When the camshaft timing exhaust gear moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

      NOTICE:
      Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear may abruptly shift in the advance direction and break the lock pin or other parts.

  1. Check for smooth rotation.

    1. Turn the camshaft timing exhaust gear within its movable range (21.5 to 23.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.

      NOTICE:
      When the air pressure is released from the advance side path and then from the retard side path, the gear automatically returns to the most advanced position due to the advance assist spring operation, and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.

  1. Check the lock at the most advanced position.

    1. Make sure that the camshaft timing exhaust gear locks at the most advanced position.

  1. Remove the vinyl tape and rubber pieces from the camshaft.

  1. Remove the bolt and camshaft timing gear.



8. INSPECT CHAIN SUB-ASSEMBLY


A168044E11
Text in Illustration 
*a
Measurement Area
  1. Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

  1. Using a vernier caliper, measure the length of 15 pins.

    Maximum chain elongation:
    137.7 mm (5.42 in.)

    HINT:
    Perform the measurement at 3 random places.

    If the elongation is more than the maximum, replace the chain sub-assembly.



9. INSPECT CRANKSHAFT TIMING SPROCKET


    A198159
  1. Place the chain around the sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    59.94 mm (2.36 in.)

    If the diameter is less than the minimum, replace the chain and crankshaft timing sprocket.

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.



10. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY


    A198160
  1. Move the stopper plate counterclockwise to release the lock. Push the plunger and check that it moves smoothly.
    If necessary, replace the No. 1 chain tensioner assembly.



11. INSPECT CHAIN TENSIONER SLIPPER


    A198161E05
  1. Measure the worn depth of the chain tensioner slipper.
    Text in Illustration 
    *a
    Depth

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the chain tensioner slipper.



12. INSPECT NO. 1 CHAIN VIBRATION DAMPER


    A198162E05
  1. Measure the worn depth of the chain vibration damper.
    Text in Illustration 
    *a
    Depth

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 1 chain vibration damper.



13. INSPECT TIMING CHAIN GUIDE


    A196926E05
  1. Measure the worn depth of the timing chain guide.
    Text in Illustration 
    *a
    Depth

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the timing chain guide.



14. INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE


    A196922
  1. Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.

    Standard thrust clearance:
    0.05 to 0.09 mm (0.00197 to 0.00354 in.)

    Maximum thrust clearance:
    0.09 mm (0.00354 in.)

    If the thrust clearance is more than the maximum, replace the engine balancer assembly.



15. INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE


    A198185
  1. Using a dial indicator, measure the thrust clearance while moving the No. 2 balance shaft back and forth.

    Standard thrust clearance:
    0.05 to 0.09 mm (0.00197 to 0.00354 in.)

    Maximum thrust clearance:
    0.09 mm (0.00354 in.)

    If the thrust clearance is more than the maximum, replace the engine balancer assembly.



16. INSPECT BALANCE SHAFT BACKLASH


    A198163E04
  1. Secure the No. 2 balance shaft in place, and then using a dial indicator, measure the backlash of the No. 1 and No. 2 balance shafts as shown in the illustration.
    Text in Illustration 
    *a
    Fix

    Standard backlash:
    0.04 to 0.17 mm (0.00157 to 0.00669 in.)

    Maximum backlash:
    0.17 m (0.00669 in.)

    NOTICE:
    Measure at 3 or more areas around the circumference of the No. 1 and No. 2 balance shafts.

    If the backlash is more than the maximum, replace the engine balancer assembly.



17. INSPECT CYLINDER HEAD BOLT


    A122880E15
  1. Using a vernier caliper, measure the diameter of the threads at the measurement point.
    Text in Illustration 
    *a
    Measurement Point

    Standard diameter:
    10.85 to 11.00 mm (0.427 to 0.433 in.)

    Minimum diameter:
    10.6 mm (0.417 in.)

    Measurement point (distance from the seat):
    106 mm (4.17 in.)

    HINT:
    1. If the diameter is less than the minimum, replace the cylinder head bolt. Failure to do so may lead to engine damage.
    2. If there is any thread deformation, replace the cylinder head bolt with a new one.



18. INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    A196896
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head.

    Maximum warpage:
    0.7 mm (0.0276 in.)

    If the warpage is more than the maximum, replace the exhaust manifold.