Home › Engine / Hybrid System ยท 1AZ-FE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REPLACEMENT

for Preparation Click here



1. REMOVE INTAKE VALVE GUIDE BUSH


A036632E01
  1. Heat the cylinder head to 80 to 100°C (176 to 212 °F).

  1. Place the cylinder head on wooden blocks.

  1. Using SST and a hammer, tap out the intake valve guide bush.

    SST
    09202-70020   (09202-00010)



2. REMOVE EXHAUST VALVE GUIDE BUSH


A036633E03
  1. Heat the cylinder head to 80 to 100°C (176 to 212 °F).

  1. Place the cylinder head on wooden blocks.

  1. Using SST and a hammer, tap out the exhaust valve guide bush.

    SST
    09202-70020   (09202-00010)



3. INSTALL INTAKE VALVE GUIDE BUSH


A131495
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a New Guide Bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    Use STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    Use O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    If the cylinder head bush bore diameter is greater than 10.306 mm (0.4057 in.), machine the bush bore to a dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) and install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212 °F).

  1. Place the cylinder head on wooden blocks.



    A036634E06
  1. Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard protrusion height:
    9.6 to 10.0 mm (0.3779 to 0.3937 in.)

    Text in Illustration 
    *a
    Protrusion Height



    A136150
  1. Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard specified clearance between the intake valve guide bush and valve stem.

    Standard oil clearance:
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)



4. INSTALL EXHAUST VALVE GUIDE BUSH


A124782
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a New Guide Bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    Use STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    Use O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    If the cylinder head bush bore diameter is greater than 10.306 mm (0.4057 in.), machine the bush bore to a dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) and install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212 °F).

  1. Place the cylinder head on wooden blocks.



    A036635E06
  1. Using SST and a hammer, tap in a new exhaust valve guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard protrusion height:
    9.6 to 10.0 mm (0.3779 to 0.3937 in.)

    Text in Illustration 
    *a
    Protrusion Height



    A124783
  1. Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard specified clearance between the exhaust valve guide bush and valve stem.

    Standard oil clearance:
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)