Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for LHD)

LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for LHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
(Click here)


3. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
(Click here)


4. REMOVE FRONT DOOR SCUFF PLATE LH


    B278977
  1. Disengage the 10 claws and remove the front door scuff plate LH.



5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the front door opening trim weatherstrip.



6. REMOVE REAR DOOR SCUFF PLATE LH


    B278979
  1. Disengage the 6 claws and remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the rear side of the scuff plate.



7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip LH.



8. REMOVE LAP BELT OUTER ANCHOR COVER


    B271081
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B271082
  1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.



10. REMOVE CENTER PILLAR LOWER GARNISH LH


    B278989
  1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.



11. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    B281558E01
  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



12. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    B279203
  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the LH side and RH side.



13. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
  1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.



    B281557
  1. Remove the bolt.

  1. Disengage the hook and remove the rear side seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



14. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    B290774E01
  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat the step above for the other hook.

  1. w/ Seat Heater System:

    1. Disconnect the 2 seat heater connectors.

  1. Remove the rear seat cushion assembly.



15. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    B279203
  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



16. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)


17. REMOVE REAR SEATBACK COVER (for Reclining Seat Type)


    B281586
  1. Disengage the 4 claws and remove the 2 rear seatback covers.

    HINT:
    Use the same procedure as for the LH side.



18. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)
  1. w/ Rear Seat Side Airbag:

    1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.

  1. Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.



    B281589
  1. Disengage the 2 hooks and disconnect the cover.

  1. Remove the 2 nuts, 2 bolts and rear seatback assembly LH.



19. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)


    B281353
  1. Remove the bolt.

  1. Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.



20. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    B281699
  1. Remove the 13 clips and luggage compartment door cover.



21. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
  1. Remove the luggage compartment floor mat.



22. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)
  1. Remove the baggage holder net.



23. REMOVE REAR FLOOR FINISH PLATE


    B294805
  1. Remove the 5 clips.



    B294806
  1. Disengage the 4 clips and remove the rear floor finish plate.



24. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    B283876E01
  1. Push the pin and remove the No. 1 luggage compartment trim hook.
    Text in Illustration 
    *1
    Pin



25. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    B281707
  1. Remove the 3 clips.

  1. Disengage the fastener and remove the luggage compartment inner trim cover LH.



26. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B280595
  1. Remove the screw.



    E227150
  1. Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



    B280598
  1. Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.



27. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    B280599
  1. Disengage the 2 clamps.



    B280639
  1. Disengage the clamp and disconnect the wire harness.



    B280600
  1. Disengage the 2 clamps and remove the 2 scuff plate clips.

  1. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.



    B283878
  1. Disengage the guide as shown in the illustration.



    B283880
  1. Disconnect the luggage door lock control cable sub-assembly.



    B293421
  1. Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.



    B287079E01
  1. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <A>



    B288519E01
  1. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <B>



    B287067E01
  1. Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.
    Text in Illustration 
    *1
    Cutout
    *2
    Guide <C>
    *3
    Guide <B>



    B287069
  1. Disengage the 2 claws and remove the fuel filler opening lid lock retainer.



  1. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.


    B280605E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Luggage Door Lock Control Cable Sub-assembly



  1. Using a knife, cut off the clamp as shown in the illustration.


    B280644E01


    Text in Illustration 
    *1
    Tape
    -
    -
    *a
    Cut
    -
    -

    NOTICE:
    Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

  1. Remove the clamp.

  1. Remove the 3 pieces of tape and luggage door lock control cable sub-assembly.