Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for RHD)

LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for RHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)
(Click here)


3. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)
(Click here)


4. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side .



6. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side .



8. REMOVE LAP BELT OUTER ANCHOR COVER

HINT:
Use the same procedure as for the LH side .



9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side .



10. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side .



11. REMOVE REAR SEAT CUSHION ASSEMBLY


    B281558E01
  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



12. REMOVE REAR SEAT CUSHION LOCK HOOK


    B279203
  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the LH side and RH side.



13. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
  1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide RH.



    B281556
  1. Remove the bolt.

  1. Disengage the hook and remove the rear side seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



14. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    B281699
  1. Remove the 13 clips and luggage compartment door cover.



15. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
  1. Remove the luggage compartment floor mat.



16. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)
  1. Remove the baggage holder net.



17. REMOVE REAR FLOOR FINISH PLATE


    B294805
  1. Remove the 5 clips.



    B294806
  1. Disengage the 4 clips and remove the rear floor finish plate.



18. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    B281722E01
  1. Push the pin and remove the No. 1 luggage compartment trim hook.
    Text in Illustration 
    *1
    Pin



19. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH


    B281708
  1. Remove the 3 clips.

  1. Disengage the fastener and remove the luggage compartment inner trim cover RH.



20. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B281743
  1. Remove the screw.



    B281744
  1. Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



    B281745
  1. Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.



21. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    B281746
  1. Disengage the 2 clamps.



    B281747
  1. Disengage the clamp and disconnect the wire harness.



    B281748
  1. Disengage the 2 clamps and remove the 2 scuff plate clips.

  1. Turn back the floor carpet so that the luggage door lock control cable sub-assembly can be removed.



    B281715E01
  1. Remove the 2 pieces of tape that connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.
    Text in Illustration 
    *1
    Tape
    *2
    Fuel Lid Lock Control Cable Sub-assembly
    *3
    Luggage Door Lock Control Cable Sub-assembly



    B283878
  1. Disengage the guide as shown in the illustration.



    B283880
  1. Disconnect the luggage door lock control cable sub-assembly.



    B281717
  1. Disengage the 2 clamps and disconnect the luggage door lock control cable sub-assembly.



  1. Disengage the 10 clamps and remove the luggage door lock control cable sub-assembly.


    B281721E01


    Text in Illustration 
    *1
    Luggage Door Lock Control Cable Sub-assembly
    *2
    Fuel Lid Lock Control Cable Sub-assembly