Home › Engine / Hybrid System ยท 2GR-FE › ENGINE MECHANICAL › CAMSHAFT

CAMSHAFT > REMOVAL

for Preparation Click here



1. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
(Click here)


2. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A205853E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-70011   (09213-70020)
    09330-00021  



    A132243
  1. Remove the 8 bolts, front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer.



3. INSTALL ENGINE ON ENGINE STAND
  1. Install the engine onto an engine stand with the bolts.



4. REMOVE ENGINE HANGERS


    A129635E18
  1. Remove the 4 bolts and 2 engine hangers.
    Text in Illustration 
    *1
    No. 1 engine hanger
    *2
    No. 2 engine hanger
    *a
    Bank 1
    *b
    Bank 2



5. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    A255337E01
  1. Disconnect the ventilation hose.
    Text in Illustration 
    *A
    Type A
    *B
    Type B

  1. Disconnect the hose clamp and union to check valve hose.



    A255505
  1. Disconnect the connector and wire harness clamp.

  1. Disconnect the 2 water by-pass hoses and fuel vapor feed hose.



    A129467
  1. Disconnect the connector from the intake air control valve assembly.



    A255338
  1. Remove the bolt and vacuum hose clamp.



    A255339
  1. Remove the bolt and separate the throttle body bracket from the intake air surge tank assembly.



    A255340
  1. Remove the bolt and separate the No. 1 surge tank stay from the intake air surge tank assembly.



    A255341
  1. Remove the 2 nuts from the intake air surge tank assembly.

  1. Using a 5 mm socket hexagon wrench, remove the 4 bolts.



    A255342
  1. Remove the intake air surge tank assembly and 3 gaskets.



6. REMOVE NO. 1 SURGE TANK STAY


    A206488
  1. Remove the bolt and No. 1 surge tank stay.



7. REMOVE THROTTLE BODY BRACKET


    A254363
  1. Remove the bolt and throttle body bracket.



8. REMOVE IGNITION COIL ASSEMBLY


    A255007
  1. Remove the nut.

  1. Disconnect the 2 harness clamps.



    A192461
  1. Disconnect the 6 ignition coil connectors.



    A136825
  1. Remove the 6 bolts and 6 ignition coils.



9. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A162388
  1. Remove the bolt and No. 2 engine mounting stay RH.



10. REMOVE INTAKE MANIFOLD


    A134933
  1. Uniformly loosen and remove the 6 bolts and 4 nuts.

  1. Remove the intake manifold and 2 gaskets.



11. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A129637
  1. Uniformly loosen and remove the 6 nuts.

  1. Remove the exhaust manifold sub-assembly RH and gasket.



12. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE


    A202567
  1. Remove the oil level dipstick.

  1. Remove the bolt and No. 2 engine oil level dipstick guide.



    A254364
  1. Remove the O-ring from the No. 2 engine oil level dipstick guide.



13. REMOVE NO. 2 MANIFOLD STAY


    A140783
  1. Remove the bolt, nut and No. 2 manifold stay.



14. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A197636
  1. Remove the 3 bolts and No. 2 exhaust manifold heat insulator.



15. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A207618
  1. Uniformly loosen and remove the 6 nuts.

  1. Remove the exhaust manifold assembly LH and gasket.



16. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A129644
  1. Remove the 5 bolts and V-ribbed belt tensioner assembly.



17. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A192400
  1. Remove the bolt and engine oil level dipstick guide.



    A171897
  1. Remove the O-ring.



18. REMOVE NO. 2 TIMING GEAR COVER


    A206492
  1. Remove the 2 bolts and No. 2 timing gear cover.



19. REMOVE WATER PUMP PULLEY


    A226686E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 4 bolts and water pump pulley.



20. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A206493
  1. Remove the bolt, No. 2 idler pulley cover plate, No. 2 idler pulley sub-assembly and idler pulley cover plate.



21. REMOVE NO. 1 VACUUM SWITCHING VALVE


    A206494
  1. Remove the bolt and No. 1 vacuum switching valve.



22. REMOVE CRANK POSITION SENSOR


    A191181
  1. Disconnect the crank position sensor connector.

  1. Remove the bolt and crank position sensor.



23. REMOVE NO. 1 OIL PIPE


    A135726E02
  1. Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.
    Text in Illustration 
    *1
    Oil Pipe Union

  1. Remove the oil control valve filter LH and gaskets.



24. REMOVE OIL PIPE


    A200607E04
  1. Remove the bolt.
    Text in Illustration 
    *1
    Oil Pipe Union
    *2
    Bolt

  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter RH and gaskets.



25. REMOVE CRANKSHAFT PULLEY


    A208600E03
  1. Using SST, loosen the crankshaft pulley bolt.

    SST
    09213-70011   (09213-70020)
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn



    A259943E01
  1. Using SST, remove the crankshaft pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    Text in Illustration 
    *a
    Hold
    V100135
    Turn



    A205852
  1. Remove the pulley set key from the crankshaft.



26. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH


    A129672
  1. Remove the 6 bolts and No. 1 front engine mounting bracket LH.

  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.



27. REMOVE WATER INLET HOUSING


    A129673
  1. Remove the 2 nuts, water inlet and thermostat.

  1. Remove the gasket.

  1. Remove the 2 stud bolts.

  1. Separate the No. 1 water by-pass hose from the water inlet housing.



    A134879E04
  1. Remove the drain cock plug.
    Text in Illustration 
    *1
    Nut
    *2
    Bolt

  1. Remove the drain cock assembly.

  1. Remove the 2 bolts, nut, and water inlet housing.



    A129675
  1. Remove the 2 O-rings.



28. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A129679
  1. Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.



    A129699
  1. Remove the 3 gaskets.



29. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A129678E05
  1. Remove the 12 bolts, seal washer, cylinder head cover sub-assembly LH and No. 2 cylinder head cover gasket.
    Text in Illustration 
    *1
    Baffle Plate

    NOTICE:
    The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the cylinder head cover sub-assembly LH.



    A129705
  1. Remove the 3 gaskets.



30. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A129680E02
  1. Remove the 16 bolts and 2 nuts.
    Text in Illustration 
    *1
    Nut



    A120816
  1. Insert the blade of the oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.

  1. Using an E6 "TORX" socket wrench, remove the 2 stud bolts.



31. REMOVE OIL STRAINER SUB-ASSEMBLY


    A129681E03
  1. Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.
    Text in Illustration 
    *1
    Bolt
    *2
    Nut

  1. Using an E6 "TORX" socket wrench, remove the 2 stud bolts.



32. REMOVE OIL PAN SUB-ASSEMBLY


    A129682E03
  1. Remove the 16 bolts and 2 nuts.
    Text in Illustration 
    *1
    Nut

    HINT:
    Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.



    A129683E02
  1. Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.



    A129684
  1. Remove the 2 O-rings.

  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.



33. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A128004E01
  1. Remove the 23 bolts and 2 nuts shown in the illustration.
    Text in Illustration 
    *1
    Nut



    A129690E03
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.

    HINT:
    Tape the screwdriver tip before use.



    A128006E01
  1. Remove the gasket.



34. REMOVE TIMING CHAIN CASE OIL SEAL


    A128007E05
  1. Using a screwdriver and wooden block, pry out the oil seal.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Wooden Block

    HINT:
    Tape the screwdriver tip before use.



35. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily tighten the pulley set bolt.



    A205165E02
  1. Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Sensor Plate
    *a
    Center Line
    *b
    Timing Mark



    A129692E07
  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    Text in Illustration 
    *a
    Timing Mark
    If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.



36. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A124589E06
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Pin

  1. Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm diameter (0.0500 in.) into the stopper plate hole.



    A095165
  1. Remove the 2 bolts and No. 1 chain tensioner assembly.



37. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the chain tensioner slipper.



38. REMOVE CHAIN SUB-ASSEMBLY


    A211711E02
  1. Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Sensor Plate
    *a
    Center Line
    *b
    Timing Mark

  1. Remove the pulley set bolt.



    A134890
  1. Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.



    A095682E13
  1. Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.
    Text in Illustration 
    *a
    for Bank 1

  1. Remove the chain sub-assembly.



39. REMOVE IDLE SPROCKET ASSEMBLY


    A129695
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.



40. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)


    A120651E08
  1. While raising the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 2 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push



    A182777E06
  1. Using SST to hold the hexagonal portion of each camshaft, loosen the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09922-10010  

    NOTICE:
    1. Be careful not to damage the cylinder head with SST.
    2. Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and the camshaft timing gear assembly together with the No. 2 chain.



41. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


    A109721
  1. Remove the bolt and No. 2 chain tensioner assembly.



42. REMOVE CAMSHAFT BEARING CAP (for Bank 1)


    A129700E08
  1. Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View



    A129701E03
  1. Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.



    A129702E01
  1. Uniformly loosen and remove the 12 bearing cap bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.



43. REMOVE CAMSHAFT
  1. Remove the camshaft.



44. REMOVE NO. 2 CAMSHAFT
  1. Remove the No. 2 camshaft.



45. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH


    A129703E02
  1. Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.

    HINT:
    Tape the screwdriver tip before use.



46. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)


    A120657E07
  1. While pushing down the No. 3 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 3 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push



    A182778E06
  1. Using SST to hold the hexagonal portion of each camshaft, loosen the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09922-10010  

    NOTICE:
    1. Be careful not to damage the cylinder head with SST.
    2. Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and the camshaft timing gear together with the No. 2 chain.



47. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


    A109722
  1. Remove the bolt and No. 3 chain tensioner assembly.



48. REMOVE CAMSHAFT BEARING CAP (for Bank 2)


    A129706E06
  1. Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View



    A134891E03
  1. Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.



    A129708E01
  1. Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.



49. REMOVE NO. 3 CAMSHAFT
  1. Remove the No. 3 camshaft.



50. REMOVE NO. 4 CAMSHAFT
  1. Remove the No. 4 camshaft.



51. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH


    A129709E02
  1. Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.