Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER

REAR BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY


    B282090
  1. Install the rear bumper reinforcement sub-assembly with the 6 nuts.

    Torque:
    61 N*m{ 622 kgf*cm , 45 ft.*lbf }



2. INSTALL WHEEL HOUSE REINFORCEMENT LH


    B280052
  1. Engage the clip.

  1. Install the wheel house reinforcement LH with the screw and nut.



3. INSTALL WHEEL HOUSE REINFORCEMENT RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL REAR BUMPER SIDE RETAINER LH


    B280046
  1. Engage the 6 claws.

  1. Install the rear bumper side retainer LH with the 3 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



5. INSTALL REAR BUMPER SIDE RETAINER RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)


    E232468E01
  1. Engage the 2 claws to install the No. 1 ultrasonic sensor retainer to the rear bumper assembly.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Keyhole
    *b
    Snap

    NOTICE:
    1. Do not damage the front bumper with the protrusion when installing the retainer.
    2. Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the front bumper.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.



7. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)


    E228019E01
  1. Engage the 2 claws to install the No. 1 ultrasonic sensor to the No. 1 ultrasonic sensor retainer.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    NOTICE:
    Push the No. 1 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.



8. INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)


    E228018E01
  1. Engage the 4 claws to install the ultrasonic sensor clip.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side



    E228017E01
  1. Engage the clamp.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

  1. Connect the connector.



9. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)


    B282083
  1. Connect the 4 connectors.

  1. Engage the 4 clamps to install the No. 2 luggage room wire.



10. INSTALL REFLEX REFLECTOR ASSEMBLY LH


    B282091
  1. Engage the guide.

  1. Install the reflex reflector assembly LH with the screw.



11. INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



12. INSTALL REAR BUMPER PAD LH
  1. Wipe off any tape adhesive residue with cleaner.



    B282079
  1. Install a new rear bumper pad LH.

    HINT:
    Stick the new rear bumper pad LH on the line marked on the rear bumper assembly.



13. INSTALL REAR BUMPER PAD RH
  1. Wipe off any tape adhesive residue with cleaner.



    B282078
  1. Install a new rear bumper pad RH.

    HINT:
    Stick the new rear bumper pad RH on the line marked on the rear bumper assembly.