Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH

LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH > INSTALLATION

for Preparation Click here



1. INSTALL BACK DOOR GARNISH MOULDING PROTECTOR LH
  1. Clean the luggage compartment door outside garnish sub-assembly.

    1. Remove any double-sided tape from the luggage compartment door outside garnish sub-assembly.

    2. Wipe off any tape adhesive residue with cleaner.



  1. Install a new back door garnish moulding protector LH.

    1. Remove the release paper from the back door garnish moulding protector LH.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    2. B283327E01
    3. Install a new back door garnish moulding protector LH as shown in the illustration.
      Standard Measurement 
      Dimension
      Measurement
      A
      1.5 mm (0.0591 in.)



2. INSTALL BACK DOOR GARNISH MOULDING PROTECTOR RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL UPPER BACK DOOR GARNISH MOULDING PROTECTOR
  1. Clean the luggage compartment door outside garnish sub-assembly.

    1. Remove any double-sided tape from the luggage compartment door outside garnish sub-assembly.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Install a new upper back door garnish moulding protector.

    1. Remove the release paper from the upper back door garnish moulding protector.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    2. Install a new upper back door garnish moulding protector.



4. INSTALL LUGGAGE COMPARTMENT DOOR EMBLEM
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Clean the luggage compartment door emblem. (If reusing the luggage compartment door emblem)

    1. Using a heat light, heat the luggage compartment door emblem.

    2. Remove the double-sided tape from the luggage compartment door emblem.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Apply new double-sided tape to the luggage compartment door emblem.



  1. Install the luggage compartment door emblem.

    1. Using a heat light, heat the vehicle body and luggage compartment door emblem.

    2. Remove the release paper from the luggage compartment door emblem.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.



    3. B282055
    4. Engage the 2 pins and install the luggage compartment door emblem as shown in the illustration.



5. INSTALL LUGGAGE ELECTRICAL KEY SWITCH COVER (w/o Smart Entry and Start System)
  1. Install the luggage electrical key switch cover.



6. INSTALL LUGGAGE DOOR OPENING SWITCH ASSEMBLY (w/ Smart Entry and Start System)
  1. Install the luggage door opening switch assembly.



7. INSTALL LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH SUB-ASSEMBLY
  1. Install 5 new gaskets to the luggage compartment door outside garnish sub-assembly.

  1. Install a new clip (back door outside garnish clip) and 2 new clips to the luggage compartment door outside garnish sub-assembly.



    B282066E01
  1. Engage the 3 clips to install the luggage compartment door outside garnish sub-assembly.
    Text in Illustration 
    *1
    Back Door Outside Garnish Clip

  1. Install the 5 nuts.

  1. w/ Smart Entry and Start System:

    1. Connect the connector.



8. INSTALL REAR LIGHT ASSEMBLY LH


    E227533E01
  1. Install the rear light assembly with the 4 nuts.

    Torque:
    Nut (A):
    3.6 N*m{ 37 kgf*cm , 32 in.*lbf }
    Nut (B):
    4.1 N*m{ 42 kgf*cm , 36 in.*lbf }

  1. Engage the clamp.

  1. Connect the connector.



9. INSTALL REAR LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL LUGGAGE COMPARTMENT DOOR COVER


    B281699
  1. Install the luggage compartment door cover with the 13 clips.