Home › Engine / Hybrid System ยท 2AR-FE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REPLACEMENT

for Preparation Click here



1. REPLACE INTAKE VALVE GUIDE BUSH
  1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.



    A194970E04
  1. Using SST and a hammer, tap out the valve guide bush.

    SST
    09201-01055  
    09950-70010   (09951-07100)



    A194985
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard bush bore diameter:
    10.285 to 10.306 mm (0.405 to 0.406 in.)

    If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.

  1. Select a new guide bush (STD or O/S 0.05), and measure its diameter.

  1. Machine the bush bore of the cylinder head to the diameter of the selected guide bush.

    Bush Bore Diameter:
    Bush Size
    Specified Condition
    STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    Standard bush length:
    41.3 to 41.7 mm (1.626 to 1.642 in.)

  1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).



    A194972E05
  1. Using SST and a hammer, tap in the selected guide bush to the standard protrusion height.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard protrusion height:
    14.8 to 15.2 mm (0.582 to 0.598 in.)

    Text in Illustration 
    *a
    Height



    A194973
  1. Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

    Standard oil clearance:
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)



2. REPLACE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.



    A194974E05
  1. Using SST and a hammer, tap out the valve guide bush.

    SST
    09201-01055  
    09950-70010   (09951-07100)



    A194975
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard bush bore diameter:
    10.285 to 10.306 mm (0.405 to 0.406 in.)

    If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.

  1. Select a new guide bush (STD or O/S 0.05), and measure its diameter.

  1. Machine the bush bore of the cylinder head to the diameter of the selected guide bush.

    Bush Bore Diameter:
    Bush Size
    Specified Condition
    STD
    10.333 to 10.344 mm (0.4068 in 0.4072 in.)
    O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    Standard bush length:
    46.8 to 47.2 mm (1.843 to 1.858 in.)

  1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).



    A194976E05
  1. Using SST and a hammer, tap in the selected guide bush to the standard protrusion height.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Standard protrusion height:
    14.2 to 14.6 mm (0.559 to 0.575 in.)

    Text in Illustration 
    *a
    Height



    A195001
  1. Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

    Standard oil clearance:
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)



3. REPLACE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.

  1. Remove the ring pins.



    A194963E01
  1. Using a plastic-faced hammer, tap in new ring pins to the cylinder head.

    Standard protrusion height:
    6.5 to 7.5 mm (0.256 to 0.295 in.)