Home › Engine / Hybrid System ยท 2AR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE ENGINE COVER JOINT


    A196900
  1. Remove the 3 joints.



2. REMOVE SPARK PLUG


    A207956
  1. Using a spark plug wrench, remove the 4 spark plugs.



3. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


  1. Camshaft timing oil control valve assembly (for exhaust side)



      A254784
    1. Disconnect the oil control valve connector.

    2. Remove the bolt and oil control valve.



    3. A195062E06
    4. Remove the O-ring from the oil control valve.
      Text in Illustration 
      *1
      O-ring



  1. Camshaft timing oil control valve assembly (for intake side)



      A254785
    1. Disconnect the oil control valve connector.

    2. Remove the bolt and oil control valve.



    3. A195062E06
    4. Remove the O-ring from the oil control valve.
      Text in Illustration 
      *1
      O-ring



4. REMOVE CAMSHAFT POSITION SENSOR


  1. Camshaft position sensor (for Exhaust Side)



      A195076
    1. Disconnect the sensor connector.

    2. Remove the bolt and sensor.



  1. Camshaft position sensor (for Intake Side)



      A254799
    1. Disconnect the sensor connector.

    2. Remove the bolt and sensor.



5. REMOVE OIL FILLER CAP SUB-ASSEMBLY
  1. Remove the oil filler cap from the cylinder head.

  1. Remove the gasket from the oil filler cap.



6. REMOVE CRANKSHAFT POSITION SENSOR


A195078
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



7. REMOVE VENTILATION VALVE SUB-ASSEMBLY


    A196036
  1. Disconnect the No. 2 ventilation hose from the ventilation valve sub-assembly.



    A196037E02
  1. Using a 19 mm deep socket wrench, remove the ventilation valve sub-assembly.
    Text in Illustration 
    *1
    19 mm Deep Socket Wrench



8. REMOVE VENTILATION CASE SUB-ASSEMBLY


    A210185
  1. Remove the 8 bolts and 2 nuts.



    A210186
  1. Remove the ventilation case by prying between the ventilation case and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and ventilation case.



9. REMOVE SEPARATOR CASE


    A210188
  1. Remove the 2 bolts, separator case and gasket.



10. REMOVE NO. 1 WATER BY-PASS PIPE


    A194876
  1. Remove the bolt, 2 nuts, water by-pass pipe and gasket.



11. REMOVE WATER INLET


    A194908
  1. Remove the 2 nuts and water inlet.



12. REMOVE V-RIBBED BELT


    A255402
  1. Attach a wrench to the hexagonal portion of the belt tensioner as shown in the illustration, rotate the belt tensioner clockwise, and remove the V-ribbed belt.



13. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A196670
  1. Remove the bolt and V-ribbed belt tensioner.



14. REMOVE ENGINE WATER PUMP ASSEMBLY


    A194904
  1. Remove the 7 bolts, engine water pump and gasket.



15. REMOVE WATER INLET HOUSING


    A195872
  1. Remove the 4 bolts, nut, inlet water housing and gasket.



16. REMOVE CRANKSHAFT PULLEY


    A195873E06
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09213-54015  
    09330-00021  
    91551-80650  



    A195874E04
  1. Using SST and the pulley bolt, remove the crankshaft pulley.
    Text in Illustration 
    *1
    Pulley Bolt
    *a
    Hold
    *b
    Turn

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)

    HINT:
    Apply a lubricant to the threads and end of SST.



17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A195876
  1. Remove the 16 bolts, 3 seal washers, cylinder head cover and gasket.



    A196857
  1. Remove the 3 gaskets from the camshaft bearing caps.



18. REMOVE SPARK PLUG TUBE GASKET


    A195877
  1. Using a screwdriver, pry out the 4 plug tube gaskets.

    NOTICE:
    Be careful not to damage the cylinder head cover.

    HINT:
    Tape the screwdriver tip before use.



19. REMOVE ENGINE MOUNTING BRACKET RH


    A196634
  1. Remove the 3 bolts and engine mounting bracket RH.



20. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A196847
  1. Remove the 17 bolts and 2 nuts.



    A196856
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, camshaft housing, cylinder block, stiffening crankcase or chain cover.

    HINT:
    Tape the screwdriver tip before use.



    A196858
  1. Remove the 3 gaskets from the stiffening crankcase.



21. REMOVE TIMING CHAIN COVER TIGHT PLUG


    A196859
  1. Using a 14 mm hexagon wrench, remove the plug and gasket.



22. REMOVE TIMING CHAIN COVER PLATE


    A196860
  1. Remove the 4 bolts, timing chain cover plate and gasket.



23. REMOVE TIMING CHAIN COVER OIL SEAL


    A210537E04
  1. Using a screwdriver and wooden block, pry out the oil seal.
    Text in Illustration 
    *1
    Wooden Block

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.



24. SET NO. 1 CYLINDER TO TDC/COMPRESSION


  1. Temporarily install the crankshaft pulley bolt.


    A200698E03


    Text in Illustration 
    *a
    Approximately 7°
    *b
    Approximately 32°
    *c
    Timing Mark
    *d
    Key

    HINT:
    "A" is not a timing mark.

  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.

  1. Remove the crankshaft pulley bolt.



25. REMOVE TIMING CHAIN GUIDE


    A196878
  1. Remove the bolt and timing chain guide.



26. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A196879E02
  1. Allow the plunger to extend slightly, and then rotate the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the tensioner.
    Text in Illustration 
    *1
    Stopper Plate
    *2
    Plunger



    A196880E02
  1. Move the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.
    Text in Illustration 
    *1
    Pin



    A196877
  1. Remove the 2 bolts, chain tensioner and gasket.



27. REMOVE CHAIN TENSIONER SLIPPER


    A196876
  1. Remove the bolt and chain tensioner slipper.



28. REMOVE CHAIN SUB-ASSEMBLY
  1. Remove the chain sub-assembly.



29. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A196868
  1. Remove the 2 bolts and chain vibration damper.



30. REMOVE CRANKSHAFT TIMING SPROCKET


    A196881
  1. Remove the crankshaft timing sprocket from the crankshaft.



31. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY


    A196882
  1. Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing gear.

    NOTICE:
    1. Be careful not to damage the cylinder head or spark plug tube with the wrench.
    2. Do not disassemble the camshaft timing gear.



32. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY


    A198183
  1. Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing exhaust gear.

    NOTICE:
    1. Be careful not to damage the cylinder head or spark plug tube with the wrench.
    2. Do not disassemble the camshaft timing exhaust gear.



33. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY


    A196884E01
  1. Uniformly loosen and remove the 20 bearing cap bolts in the sequence shown in the illustration.



    A196899
  1. Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.



34. REMOVE CAMSHAFT BEARING CAP


    A196885E01
  1. Remove the 11 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.



35. REMOVE OIL CONTROL VALVE FILTER


    A196915
  1. Remove the oil control valve filter from the No. 1 camshaft bearing cap.



36. REMOVE CAMSHAFT
  1. Remove the camshaft and No. 2 camshaft.



37. REMOVE NO. 1 CAMSHAFT BEARING


    A196916
  1. Remove the No. 1 camshaft bearing.



38. REMOVE NO. 2 CAMSHAFT BEARING


    A196917
  1. Remove the No. 2 camshaft bearing.



39. REMOVE CAMSHAFT HOUSING STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.



40. REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.



41. REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:
It is not necessary to remove the straight pin unless it is being replaced.



42. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 16 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



43. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 16 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



44. REMOVE VALVE STEM CAP
  1. Remove the 16 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



45. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    A196908E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    HINT:
    Be sure to keep the removed parts separate for each installation position.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in the incorrect order.

  1. Remove the cylinder head.



46. REMOVE CYLINDER HEAD GASKET
  1. Remove the cylinder head gasket from the cylinder block.



47. REMOVE CYLINDER BLOCK WATER JACKET SPACER


    A196938
  1. Remove the cylinder block water jacket spacer from the cylinder block.

    NOTICE:
    Be sure to remove the water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block is inverted.



48. REMOVE OIL FILTER CAP ASSEMBLY


    A204919E06
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A196672
  1. Remove the oil filter drain plug from the oil filter cap.



    A196673E04
  1. Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Valve
    *2
    Cap
    *3
    O-ring
    *4
    Pipe

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A196674
  1. Check that the oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.



    A215914E02
  1. Using SST, remove the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.



    A196675E07
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap
    *3
    O-ring

    NOTICE:
    Be sure to remove the O-ring by hand, without using any tools, to prevent damage to the O-ring groove.



49. REMOVE OIL PAN SUB-ASSEMBLY


    A210204E03
  1. Remove the 11 bolts and 2 nuts.
    Text in Illustration 
    *1
    Nut



    A118769
  1. Insert the blade of an oil pan seal cutter between the oil pan and stiffening crankcase, cut off the applied sealer and remove the oil pan.

    NOTICE:
    1. Be careful not to damage the stiffening crankcase contact surface of the oil pan.
    2. Be careful not to damage the stiffening crankcase flange.



50. REMOVE OIL STRAINER SUB-ASSEMBLY


    A196919
  1. Remove the 3 bolts, oil strainer and gasket.



51. REMOVE NO. 1 OIL PAN BAFFLE PLATE


    A196920
  1. Remove the 5 bolts and oil pan baffle plate.



52. INSPECT CRANKSHAFT BACKLASH


    A196931
  1. Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

    Maximum backlash:
    0.20 mm (0.00787 in.)

    If the backlash is more than the maximum, replace the engine balancer assembly.



53. REMOVE ENGINE BALANCER ASSEMBLY


    A196921
  1. Remove the 7 bolts and engine balancer.

    NOTICE:
    Do not disassemble the engine balancer.



54. INSPECT BALANCE SHAFT THRUST CLEARANCE


    A196922
  1. Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.

    Standard thrust clearance:
    0.05 to 0.09 mm (0.00197 to 0.00354 in.)

    Maximum thrust clearance:
    0.09 mm (0.00354 in.)

    If the thrust clearance is more than the maximum, replace the engine balancer assembly.



55. REMOVE STIFFENING CRANKCASE ASSEMBLY


    A196933
  1. Remove the 7 bolts.



    A196934E03
  1. Using a screwdriver, remove the stiffening crankcase by prying between the stiffening crankcase and cylinder block at the places shown in the illustration.
    Text in Illustration 
    *a
    LH Side:
    *b
    RH Side:

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and stiffening crankcase.



56. REMOVE STIFFENING CRANKCASE STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.



57. REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.



58. REMOVE REAR ENGINE OIL SEAL


    A196937
  1. Remove the rear engine oil seal from the cylinder block.