AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > OPERATION CHECK |
| CHECK PANEL & STEERING SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.
![]() |
Panel & Steering Switch Check Mode
| Display | Content |
| *a: Switch condition | "Pushed" is displayed when any switch is pushed |
| *b: Number of switches pushed |
|
| *c: Rotary switch direction | Direction of rotary switch is displayed |
Operate each switch and check that the switch conditions are correctly displayed.
| CHECK TOUCH SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Touch Switch" from the "Function Check/Setting I" screen.
![]() |
Touch Switch Check
Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.
| CHECK MICROPHONE & VOICE RECOGNITION |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Mic & Voice Recognition" from the "Function Check/Setting I" screen.
![]() |
Microphone & Voice Recognition Check
| Display | Content |
| *a: Microphone input level meter | Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels. |
When speaking into the microphone, check that the microphone input level meter changes according to the input level.
| CHECK COLOR BAR |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Color Bar" from the "Function Check/Setting I" screen.
![]() |
Color Bar Check Mode
Select a color bar from the "Color Bar Check Mode" screen.
Check the display color.
| CHECK VEHICLE SIGNAL |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Vehicle Signal" from the "Function Check/Setting I" screen.
![]() |
Vehicle Signal Check Mode
| Display | Content |
| Battery | Battery voltage is displayed. |
| IG | Ignition switch ON/OFF state is displayed. |
| PKB | Parking brake ON/OFF state is displayed. |
| REV | Reverse signal ON/OFF state is displayed. |
| SPEED | Vehicle speed is displayed in km/h. |
| TAIL | Tail signal (Light control switch) ON/OFF state is displayed. |
| ADIM/TCAN | Brightness state DIM (with) / BRIGHT (without) is displayed. |
When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
| CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.
![]() |
Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)
| Display | Content |
| *a: Receive voice level adjustment | Setting for the voice level received from "Bluetooth" compatible phones. |
| *b: Send voice level adjustment | Setting for the voice level sent from "Bluetooth" compatible phones. |
If the voice level is low, press the up button, and if the voice level is loud, press the down button.
![]() |
Hands-Free Voice Quality Setting (Voice Quality Type adjustment)
| *a | Numeric keypad |
| *b | Setting button |
| *c | Reset button |
If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.
When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.
| Parameter | Target Phenomenon | Voice Quality Type (FUJITSU TEN) | Voice Quality Type (Panasonic) | Voice Quality Type (Pioneer) | Positive Effects of Changing Voice Quality | Negative Effects of Changing Voice Quality |
| Echo | The other party hears a lot of echo when speaking to you. | 1000 2000 | 0001 | 0001 0002 0003 0004 0005 | The amount of echo the other party hears of their own voice is reduced. | When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc. |
| Half Duplex | When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc. | 0100 0200 | 0002 | 0010 0020 0030 0040 0050 | When both parties speak at the same time, the phenomenon by which the other party's voice suddenly drops in volume, cuts out etc. reduces. | The amount of echo the other party hears of their own voice increases. |
| Noise | The other party hears a lot of vehicle noise etc. when listening to your voice. | 0010 0020 | 0004 | 0100 0200 0300 0400 0500 | The amount of vehicle noise etc. the other party hears when listening to your voice reduces. | The quality of your voice, that the other party hears, reduces. |
| Voice Quality | The quality of your voice, that the other party hears, is low. | 0001 0002 | 0003 | 1000 2000 3000 4000 5000 | The quality of your voice, that the other party hears, increases. | The amount of noise etc. the other party hears when listening to your voice increases. |
| CHECK UNIT VERSION INFORMATION |
Enter diagnostic mode (Click here).
![]() |
Select "Service Information" from the "Service Menu" screen.
![]() |
Select "Version Information" from the "Service Information" screen.
![]() |
Press the "Push" switch.
![]() |
Unit Version Information
| Display | Content |
| *a: Device name | Target device |
| *b: Manufacturer name | Manufacturer of the ECU (target device) |
| *c: Component name | Component name of the ECU (target device) |
| *d: Version | Version of the ECU (target device) |
| CHECK SOFTWARE ERROR HISTORY |
Check software error history.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Navigation System/ Utility / Software Error History.
When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.
| Error Description | Trigger | Detail |
| Software Reset | Navi Microcomputer | Hexadecimal Number |
| Audio Microcomputer | ||
| CAN Microcomputer | ||
| No Video Signal | Front Monitor | |
| Rear Monitor | ||
| MOST Cold Restart | Always |
Clear software error history.
When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (Click here).
| CHECK OPTICAL DISC ERROR HISTORY |
Check optical disc error history.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Navigation System/ Utility / Optical Disc Error History.
When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.
| Display | Content |
| Error Type | Displays the type of error. |
| Device | Displays the malfunctioning device. |
| Date | Displays the date and time that the malfunction occurred. |
| Error Type | Detection Condition | Action |
| Read Error | When a disc read error occurs. | Proceed to next suspected area shown in Problem Symptoms Table (Click here) |
| Disc damaged/upside down/dirty | When it is determined that any of the following is the cause of the disc read error:
| |
| Cannot determine disc type | An unsuitable disc is inserted. | |
| DPS error | When an error occurs while decoding MP3/WMA files. | |
| Some files are corrupt |
| |
| Some files cannot be found |
| |
| Copy protection violation | When a file with copyright protection that cannot be played back is played back. |
| Device | Component |
| DVD-P | Not available |
| CD-P | Radio and display receiver assembly |
| R-Seat DVD-P | Not available |
Clear optical disc error history.
When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (Click here).