DTC B27A1 Open in Driver Side Electrical Antenna Circuit |
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B27A1 | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*). |
| Any time |
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
| Entry lock/unlock operation cannot be performed for driver door | - |
| DTC Code | Data List and Active Test |
| B27A1 | Key diagnostic mode can be used to perform troubleshooting |

| 1.CHECK CONNECTOR CONNECTION |
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE) |
Disconnect the I78 and A43 certification ECU (smart key ECU assembly) connector.
Disconnect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I78-12 (CLG1) - W1-6 (ANT1) | Always | Below 1 Ω |
| I78-13 (CG1B) - W1-3 (ANT2) | Always | Below 1 Ω |
| A43-11 (E) - Body ground | Always | Below 1 Ω |
| W1-2 (GND) - Body ground | Always | Below 1 Ω |
| I78-12 (CLG1) or W1-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| I78-13 (CG1B) or W1-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I78-12 (CLG1) - V1-6 (ANT1) | Always | Below 1 Ω |
| I78-13 (CG1B) - V1-3 (ANT2) | Always | Below 1 Ω |
| A43-11 (E) - Body ground | Always | Below 1 Ω |
| V1-2 (GND) - Body ground | Always | Below 1 Ω |
| I78-12 (CLG1) or V1-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| I78-13 (CG1B) or V1-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA) |
Connect the I78 and A43 certification ECU (smart key ECU assembly) connector.

| *1 | Waveform 1 | *2 | Waveform 2 |
| *a | Component with harness connected (Certification ECU (smart key ECU assembly)) | - | - |
Connect the W1*3 or V1*4 front door outside handle assembly (for driver door) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
| I78-12 (CLG1) - A43-11 (E) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 1) |
| I78-12 (CLG1) - A43-11 (E) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
| I78-13 (CG1B) - A43-11 (E) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
|
| ||||
| OK | |
| 4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) |
Temporarily replace the front door outside handle assembly (for driver door) with a new or known good one (Click here).
| NEXT | |
| 5.CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 6.CHECK FOR DTC |
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||