Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

DTC    B27A6    Open in Rear Floor Electrical Key Oscillator Circuit

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key antenna assembly (rear floor). For the No. 2 indoor electrical key antenna assembly (rear floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A6 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor) (between terminals CLG6 and CLG4, or terminals CG6B and CLGB).

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B27A6
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor) (CLG6 - CLG4, CG6B - CLGB) (1 trip detection logic*).
  1. Wire harness or connector
  2. No. 2 indoor electrical key antenna assembly (rear floor)
  3. Certification ECU (smart key ECU assembly)
Any time
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in rear seat area:
  1. Power source mode does not change when engine switch pressed
  2. Electrical key transmitter sub-assembly locked inside vehicle
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B27A6
Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM


B274845E16


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  4. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
  5. The No. 2 indoor electrical key antenna assembly (rear floor) has an antenna coil between CLG4 and CLGB terminals.

1.CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY ANTENNA)
  1. Disconnect the O1 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the N10 No. 2 indoor electrical key antenna assembly (rear floor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O1-11 (CLG6) - N10-1 (CLG4)
    Always
    Below 1 Ω
    O1-10 (CG6B) - N10-3 (CLGB)
    Always
    Below 1 Ω
    A43-11 (E) - Body ground
    Always
    Below 1 Ω
    O1-11 (CLG6) or N10-1 (CLG4) - Body ground
    Always
    10 kΩ or higher
    O1-10 (CG6B) or N10-3 (CLGB) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)


  1. Connect the O1 certification ECU (smart key ECU assembly) connector.


    B271428E06


    Text in Illustration 
    *1
    Waveform
    -
    -
    *a
    Component with harness connected
    (Certification ECU (smart key ECU assembly))
    *b
    Within approximately 30 seconds from when the door is closed
    *c
    After approximately 30 seconds from when the door is closed
    -
    -

  1. Connect the N10 No. 2 indoor electrical key antenna assembly (rear floor) connector.

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    O1-11 (CLG6) - A43-11 (E)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform)
    O1-10 (CG6B) - A43-11 (E)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform)



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
  1. Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new or known good one (Click here).


NEXT


5.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


6.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B27A6 is not output.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR) WAS DEFECTIVE)