Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)
  1. Disable the auto away/return function by changing the customize parameter (Click here).

    NOTICE:
    Record the current customize parameter setting (whether the auto away/return function is enabled or disabled) in order to restore the current setting after finishing this operation.

    HINT:
    Performing the above operation disables the auto away/return function when the ignition switch is turned off.

  1. Turn the ignition switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

  1. Turn the ignition switch off and disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE FRONT DOOR SCUFF PLATE LH


    B278977
  1. Disengage the 10 claws and remove the front door scuff plate LH.



5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B278978
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



6. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B284921
  1. Disconnect the front door opening trim weatherstrip LH.



7. REMOVE INSTRUMENT SIDE PANEL LH


    B280320
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B280322
  1. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.



8. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)


    B281782
  1. Disengage the 2 claws and 4 clips to remove the upper instrument panel finish panel as shown in the illustration.

  1. w/ Smart Entry and Start System:

    1. Disconnect the connector.



9. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B280324
  1. Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.



10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
  1. for Manual Tilt and Manual Telescopic Steering Column:

    1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.



    B283374
  1. Using a moulding remover, disengage the 4 clips and 2 guides.



  1. for LHD:



      B280326
    1. Disengage the 3 claws, 7 clips and 4 guides.



  1. for RHD:



      B281784
    1. Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.

  1. Disconnect each connector.



    B280329
  1. Remove the instrument cluster finish panel assembly as shown in the illustration.



11. REMOVE COMBINATION METER ASSEMBLY


    E226414
  1. Remove the 4 screws.



    E223142
  1. Disengage the wire harness clamp.

  1. Disconnect the 2 connectors to remove the combination meter assembly.



12. REMOVE FRONT PANEL GARNISH LH


    B280331
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.



13. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



14. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY


    B280327
  1. Remove the 2 bolts <B>.



  1. w/o Driver Side Knee Airbag:



      B281943
    1. Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.



  1. w/ Driver Side Knee Airbag:



      B280328
    1. Disengage the 4 claws, 7 clips and 3 guides to remove the instrument panel sub-assembly.



15. REMOVE FRONT PANEL GARNISH RH


    B280332
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish RH.



16. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B281911
  1. Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.



17. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
  1. Move the shift lever to N.



  1. Disengage the 6 clips as shown in the illustration.


    B280335

  1. Disconnect each connector to remove the rear console upper panel sub-assembly.



18. REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY


    B278005
  1. Remove the 2 screws.



    B277989
  1. Disengage the 4 clips and 2 guides as shown in the illustration.



    B280337
  1. Disengage the clamp.

  1. Disconnect the 2 connectors to remove the upper console box sub-assembly.



19. REMOVE NO. 4 CONSOLE BOX DUCT


    B293623
  1. Disengage the claw and remove the No. 4 console box duct.



20. REMOVE CONSOLE BOX CARPET


    B279873
  1. Remove the console box carpet.



21. REMOVE CONSOLE BOX ASSEMBLY


    B280338
  1. Remove the 2 bolts and 2 screws.



    B281750
  1. Pull the console box assembly in the direction indicated by the arrow to disengage the 4 guides and remove the console box assembly.



22. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B281758
  1. Using a moulding remover, pry up on the center instrument cluster finish panel sub-assembly until there is enough of a gap to make it possible to pull on the panel by hand.



    B281757
  1. Pull the center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 7 clips and 2 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.



23. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    B281759
  1. Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 clips as shown in the illustration.

  1. Disconnect the connector to remove the No. 2 instrument panel register assembly.



24. REMOVE FRONT CONSOLE UPPER PANEL GARNISH


  1. for Blank Type:



      B284922
    1. Disengage the 2 claws and remove the front console upper panel garnish as shown in the illustration.



  1. for 3 Switch Hole Type:



      B281752
    1. Disengage the 2 claws as shown in the illustration.

    2. Disconnect the each connector to remove the front console upper panel garnish.



25. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    B281754
  1. Remove the 2 screws <C>.



    B281755
  1. Disengage the 2 clips as shown in the illustration.

  1. Disconnect each connector to remove the front ash receptacle assembly.



26. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)


    E227930E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    E227932
  1. Remove the 4 bolts.



    E227934
  1. Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.



27. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)


    E227929E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    E227931
  1. Remove the 4 bolts.



    E227933
  1. Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.



28. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



29. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side .



30. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B284920
  1. Disconnect the front door opening trim weatherstrip RH.



31. REMOVE INSTRUMENT SIDE PANEL RH


    B281763
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B281765
  1. Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.



32. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B279888
  1. Disengage the 4 claws.

  1. Disengage the 2 guides.

  1. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.



33. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B281767
  1. Remove the bolt <B> and screw <C>.

  1. Open the lower instrument panel door.



    B281768
  1. Remove the 3 screws <C>.



    B281769
  1. Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.



34. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    B281771
  1. Using a moulding remover, disengage the 10 clips to remove the No. 3 instrument panel register assembly as shown in the illustration.



35. REMOVE FRONT PILLAR GARNISH LH


    B278985E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    Make the front pillar garnish LH hang down from the front pillar garnish clip.



    B278986E01
  1. While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

  1. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.



    B278988E01
  1. Protect the curtain shield airbag assembly.
    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Protective Cover
    *3
    Curtain Shield Airbag Assembly

    1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



36. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B280301E01
  1. Apply protective tape to the areas shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B280302
  1. Using a moulding remover, disengage the 2 clips and 3 claws.

  1. Disengage the 2 guides to remove the No.1 instrument panel speaker panel sub-assembly.



37. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    E231530
  1. Remove the 2 screws.



    E226777
  1. Lift the front No. 2 speaker assembly and disconnect the connector to remove the speaker.

    NOTICE:
    Do not touch the speaker cone.



38. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY


    B281761
  1. Disengage the 6 clips as shown in the illustration.

  1. Disconnect the connector to remove the No. 1 speaker opening cover assembly.



39. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)


    E223721
  1. Remove the 2 screws.



    E223722
  1. Lift the front No. 3 speaker assembly and disconnect the connector to remove the speaker.

    NOTICE:
    Do not touch the speaker cone.



40. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side .



41. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B279896E01
  1. Apply protective tape to the areas shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B279897
  1. Using a moulding remover, disengage the 2 clips and 3 claws.

  1. Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.



42. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure as for the LH side .



43. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


  1. for LHD:



      B280290
    1. Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.



    B281774
  1. Remove the 2 screws <C>.



    B281775
  1. Disengage the clip and 4 guides to remove the front No. 2 console box insert as shown in the illustration.



44. REMOVE CONSOLE BOX INSERT


  1. for RHD:



      B281942
    1. Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.



    B281777
  1. Remove the 2 screws <C>.



    B281778
  1. Disengage the clip and 4 guides to remove the console box insert as shown in the illustration.



45. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B294944
  1. Disengage the 3 clips and guide to remove the lower instrument panel finish panel assembly.

  1. for LHD with Smart Entry and Start System:

    1. Disconnect the connector.



46. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


  1. Disengage the 10 clips to remove the No.1 instrument panel garnish sub-assembly as shown in the illustration.


    B280294



47. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B288991E01
  1. Slide the slider to release the lock, and then disconnect the connector.
    Text in Illustration 
    *a
    Slider

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



48. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY


  1. Disconnect each connector.


    B281788E01


    Text in Illustration 
    *A
    w/ Ion Generator
    -
    -

  1. Disengage each clamp.



    B284917
  1. Disconnect the glove box light as shown in the illustration.



  1. Remove the 2 passenger airbag bolts <A>.


    B281789E01


    Text in Illustration 
    *1
    Passenger Airbag Bolt <A>
    *2
    Bolt <B>
    *3
    Nut <E> or <F>
    *4
    Clip

  1. Remove the 3 bolts <B> and nut <E> or <F>.

  1. Remove the 2 clips.



  1. Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.


    B281790

    NOTICE:
    1. Do not damage the instrument panel safety pad assembly.
    2. Do not allow the wire harnesses to interfere with the surrounding parts.