Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > DISASSEMBLY

for Preparation Click here



1. REMOVE NO. 1 INSTRUMENT PANEL PIN


  1. Remove the 4 screws <C> and 4 No. 1 instrument panel pins.


    B281902



2. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.



    B286454
  1. Remove the 2 screws.



    B286458
  1. Lean the instrument panel safety pad assembly and disengage the 3 hooks.



    B286459
  1. Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad assembly.



3. REMOVE NO. 1 HEATER TO REGISTER DUCT (except LHD with Ion Generator)


    B281903
  1. Remove the clip.

  1. Remove the 3 screws <C> and No. 1 heater to register duct.



4. REMOVE HEATER TO REGISTER DUCT ASSEMBLY (for LHD with Ion Generator)


    B281905
  1. Remove the clip.

  1. Remove the 3 screws <C>.

  1. Disengage the heater to register duct assembly from the ion generator assembly, to remove the heater to register duct.



5. REMOVE NO. 3 HEATER TO REGISTER DUCT (for LHD)


    B281907
  1. Remove the clip.

  1. Remove the 3 screws <C> and No. 3 heater to register duct.



6. REMOVE HEATER TO REGISTER DUCT ASSEMBLY (for RHD)


    B281904
  1. Remove the clip.

  1. Remove the 3 screws <C>.

  1. Disengage the heater to register duct assembly from the ion generator assembly, to remove the heater to register duct.



7. REMOVE ION GENERATOR ASSEMBLY (w/ Ion Generator)


    B281906
  1. Remove the 3 screws and ion generator assembly.



8. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT


    B277982
  1. Remove the screw <C>.

  1. Disengage the 2 claws to remove the No. 1 side defroster nozzle duct.



9. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT


    B281908
  1. Remove the screw <C>.

  1. Disengage the 2 claws to remove the No. 2 side defroster nozzle duct.



10. REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)


  1. Disengage the 8 clamps and remove the antenna cord sub-assembly.


    E226780



11. REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)


  1. Disengage the 10 clamps and remove the antenna cord sub-assembly.


    E227950



12. REMOVE DEFROSTER NOZZLE ASSEMBLY


    B277984
  1. Remove the 3 screws <C>.

  1. Disengage the 2 guides to remove the defroster nozzle assembly.



13. REMOVE NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System)


    E223756
  1. Remove the 2 screws.

  1. Disengage the 2 clamps and remove the navigation antenna assembly.



14. REMOVE NO. 2 HEATER TO REGISTER DUCT


    B277985
  1. Remove the 2 screws <C> and No. 2 heater to register duct.



15. REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    B277986
  1. Remove the 2 screws <C>.



  1. Apply protective tape to the areas shown in the illustration.


    B281909E01


    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Disengage the 6 clips for No. 2 instrument panel garnish sub-assembly lower part as shown in the illustration.

  1. Using a moulding remover, disengage the 8 clips to remove the No. 2 instrument panel garnish sub-assembly as shown in the illustration.