Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1479/79    Flow Sensor Circuit

for Preparation Click here


DESCRIPTION

The A/C flow sensor, which is mounted on the compressor, is used to detect the amount of refrigerant flow. The A/C flow sensor converts the amount of refrigerant flow that is detected to a voltage value to send it to the air conditioning amplifier assembly. The voltage value sent from the A/C flow sensor changes depending on the amount of refrigerant flow. As the amount of refrigerant flow becomes larger, the voltage becomes lower. As the amount of refrigerant flow becomes smaller, the voltage becomes higher. The air conditioning amplifier assembly supplies 5 V to the A/C flow sensor and monitors changes in the voltage value sent from the A/C flow sensor. The air conditioning amplifier assembly then sends a signal to the ECM via CAN communication to allow the ECM to control the engine speed while the air conditioning is on.

DTC No.
DTC Detection Condition
Trouble Area
B1479/79
Open or short in A/C flow sensor circuit
  1. Compressor assembly with pulley (A/C flow sensor)*1
  2. Cooler compressor assembly (A/C flow sensor)*2
  3. Harness or connector between compressor assembly with pulley (A/C flow sensor) and air conditioning amplifier assembly*1
  4. Harness or connector between cooler compressor assembly (A/C lock sensor) and air conditioning amplifier assembly*2
  5. Air conditioning amplifier assembly
  1. *1: for 2AR-FE
  2. *2: for 2GR-FE

WIRING DIAGRAM


E227647E01


INSPECTION PROCEDURE

1.CONFIRM MODEL

Result:
Result
Proceed to
for 2AR-FE
A
for 2GR-FE
B



B
Go to step 6
A


2.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Flow Sensor
    A/C flow sensor /
    Min.: 0 V
    Max.: 5 V
    A/C on, Blower switch HI: 0.7 to 3.8 V
    A/C off, Blower switch off: 3.8 to 4.2 V
    A/C flow sensor is malfunctioning when a constant value between 0.7 and 4.2 V is displayed continuously for more than 4 seconds.

    OK:
    The display is as specified in the Normal Condition column.


    Result:

    Result
    Proceed to
    OK (When troubleshooting according to Problem Symptoms Table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG (When a constant value between 0.7 and 4.2 V is displayed continuously for more than 4 seconds)
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 4
A


3.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Cutoff Signal
    A/C control cutoff signal /
    OFF or ON
    A/C switch on: OFF
    A/C switch off: ON
    -

    Result:

    Result
    Proceed to
    Value in Data List indicates OFF
    A
    Value in Data List indicates ON
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


4.REPLACE COMPRESSOR ASSEMBLY WITH PULLEY (A/C FLOW SENSOR)
  1. Replace the compressor assembly with pulley (A/C flow sensor) (Click here).

    HINT:
    Since the compressor assembly with pulley (A/C flow sensor) cannot be inspected while it is removed from the vehicle, replace the compressor assembly with pulley (A/C flow sensor) with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1479/79 is not output
    A
    DTC B1479/79 is output
    B



B
Go to step 5
A

END 

5.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (A/C FLOW SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I77-7 (FLOQ) - E75-3 (QUFL)
    Always
    Below 1 Ω
    I77-13 (SG-2) - E75-2 (SGFL)
    Always
    Below 1 Ω
    I77-30 (S5-1) - E75-1 (S5FL)
    Always
    Below 1 Ω
    I77-7 (FLOQ) - Body ground
    Always
    10 kΩ or higher
    I77-13 (SG-2) - Body ground
    Always
    10 kΩ or higher
    I77-30 (S5-1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

6.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Flow Sensor
    A/C flow sensor /
    Min.: 0 V
    Max.: 5 V
    A/C on, Blower switch HI: 0.7 to 3.8 V
    A/C off, Blower switch off: 3.8 to 4.2 V
    A/C flow sensor is malfunctioning when a constant value between 0.7 and 4.2 V is displayed continuously for more than 4 seconds.

    OK:
    The display is as specified in the Normal Condition column.


    Result:

    Result
    Proceed to
    OK (When troubleshooting according to Problem Symptoms Table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG (When a constant value between 0.7 and 4.2 V is displayed continuously for more than 4 seconds)
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 8
A


7.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Cutoff Signal
    A/C control cutoff signal /
    OFF or ON
    A/C switch on: OFF
    A/C switch off: ON
    -

    Result:

    Result
    Proceed to
    Value in Data List indicates OFF
    A
    Value in Data List indicates ON
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


8.REPLACE COOLER COMPRESSOR ASSEMBLY (A/C FLOW SENSOR)
  1. Replace the cooler compressor assembly (A/C flow sensor) (Click here).

    HINT:
    Since the cooler compressor assembly (A/C flow sensor) cannot be inspected while it is removed from the vehicle, replace the cooler compressor assembly (A/C flow sensor) with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1479/79 is not output
    A
    DTC B1479/79 is output
    B



B
Go to step 9
A

END 

9.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (A/C FLOW SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I77-7 (FLOQ) - E75-3 (QUFL)
    Always
    Below 1 Ω
    I77-13 (SG-2) - E75-2 (SGFL)
    Always
    Below 1 Ω
    I77-30 (S5-1) - E75-1 (S5FL)
    Always
    Below 1 Ω
    I77-7 (FLOQ) - Body ground
    Always
    10 kΩ or higher
    I77-13 (SG-2) - Body ground
    Always
    10 kΩ or higher
    I77-30 (S5-1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)