Home › General › SPECIFICATIONS › U760E AUTOMATIC TRANSMISSION / TRANSAXLE

U760E AUTOMATIC TRANSMISSION / TRANSAXLE > SERVICE DATA



Line pressure (Wheel locked)
Engine idling
D position
360 to 430 kPa (3.7 to 4.4 kgf/cm2, 52 to 62 psi)
R position
670 to 820 kPa (6.8 to 8.4 kgf/cm2, 97 to 119 psi)
At stall speed (Throttle valve fully open)
D position
1160 to 1350 kPa (11.8 to 13.8 kgf/cm2, 168 to 196 psi)
R position
1650 to 1910 kPa (16.8 to 19.5 kgf/cm2, 239 to 277 psi)
Engine stall speed
D position
2330 to 2930 rpm
Time lag
N → D position
Less than 1.2 seconds
N → R position
Less than 1.5 seconds
Engine idle speed (A/C OFF)
N position
600 to 700 rpm
Shift schedule
D position
Throttle valve fully open (Normal)
1 → 2
45 to 55 km/h (28 to 34 mph)
2 → 3
85 to 95 km/h (53 to 59 mph)
3 → 4
120 to 130 km/h (75 to 81 mph)
4 → 5
175 to 185 km/h (109 to 115 mph)
5 → 6
255 to 270 km/h (158 to 168 mph)
Throttle valve opening 6% (Normal)
1 → 2
10 to 20 km/h (6 to 12 mph)
2 → 3
20 to 30 km/h (12 to 19 mph)
3 → 4
25 to 40 km/h (16 to 25 mph)
4 → 5
45 to 55 km/h (28 to 34 mph)
5 → 6
60 to 70 km/h (37 to 43 mph)
5, 4, 3, 2, 1 gear range
Manual downshift speed
→ 5
280 to 295 km/h (174 to 183 mph)
→ 4
190 to 200 km/h (118 to 124 mph)
→ 3
130 to 140 km/h (81 to 87 mph)
→ 2
95 to 110 km/h (59 to 68 mph)
→ 1
35 to 45 km/h (22 to 28 mph)

Shift solenoid valve SL
Tester Connection
Condition
Specified Condition
Solenoid connector - Solenoid body
20°C (68°F)
11 to 15 Ω
Shift solenoid valve SLT
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Shift solenoid valve SLU
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Shift solenoid valve SL1
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Shift solenoid valve SL2
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Shift solenoid valve SL3
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Shift solenoid valve SL4
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Park/Neutral position switch
Tester Connection
Shift Lever Position
Specified Condition
1 (RB) - 2 (RL)
R
Below 1 Ω
Except R
10 kΩ or higher
1 (RB) - 3 (PL)
P
Below 1 Ω
Except P
10 kΩ or higher
1 (RB) - 7 (DL)
D, S, "+" or "-"
Below 1 Ω
Except D, S, "+" and "-"
10 kΩ or higher
1 (RB) - 8 (NL)
N
Below 1 Ω
Except N
10 kΩ or higher
4 (B) - 9 (L)
P or N
Below 1 Ω
Except P and N
10 kΩ or higher
Lower shift lever assembly (w/o Smart Entry and Start System)
Tester Connection
Condition
Specified Condition
1 (ACC) - Body ground
Ignition switch ON
11 to 14 V
Ignition switch ACC
11 to 14 V
Ignition switch off
Below 1 V
8 (STP) - Body ground
Brake pedal depressed
11 to 14 V
Brake pedal released
Below 1 V
5 (KLS+) - Body ground
Ignition switch ACC and shift lever in P
Below 1 V
Ignition switch ACC and shift lever except in P (Within approx. 1 second)
7.5 to 11 V
Ignition switch ACC and shift lever in P (After approx. 1 second)
6.0 to 9.5 V
4 (IG) - Body ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
Tester Connection
Condition
Specified Condition
7 (E) - Body ground
Always
Below 1 Ω
Lower shift lever assembly (w/ Smart Entry and Start System)
Tester Connection
Condition
Specified Condition
5 (IG) - Body ground
Engine switch on (IG)
11 to 14 V
Engine switch off
Below 1 V
4 (STP) - Body ground
Brake pedal depressed
11 to 14 V
Brake pedal released
Below 1 V
Tester Connection
Condition
Specified Condition
1 (E) - Body ground
Always
Below 1 Ω
Transmission control switch (for LHD)
Tester Connection
Condition
Specified Condition
4 (IG) - 5 (S)
Shift lever in S, "+" or "-"
Below 1 Ω
Shift lever not in S, "+" or "-"
10 kΩ or higher
3 (SFTU) - 2 (E)
Shift lever held in "+" (Up-shift)
Below 1 Ω
Shift lever not held in "+"
10 kΩ or higher
1 (SFTD) - 2 (E)
Shift lever held in "-" (Down-shift)
Below 1 Ω
Shift lever not held in "-"d
10 kΩ or higher
Transmission control switch (for RHD)
4 (IG) - 5 (S)
Shift lever in S, "+" or "-"
Below 1 Ω
Shift lever not in S, "+" or "-"
10 kΩ or higher
1 (SFTU) - 2 (E)
Shift lever held in "+" (Up-shift)
Below 1 Ω
Shift lever not held in "+"
10 kΩ or higher
3 (SFTD) - 2 (E)
Shift lever held in "-" (Down-shift)
Below 1 Ω
Shift lever not held in "-"d
10 kΩ or higher
Shift lock solenoid
Tester Connection
Shift Lever Position
Specified Condition
4 (P) - 3 (E2)
P
10 kΩ or higher
Except P
Below 1 Ω
Tester Connection
Condition
Specified Condition
1 (SLS+) - 2 (SLS-)
Always
112 Ω
Transaxle case oil seal tap in depth
Standard
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Front transaxle case oil seal tap in depth
Standard
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Drive plate runout
Maximum
0.30 mm (0.0118 in.)
Input shaft end play
Standard
0.020 to 1.242 mm (0.000788 to 0.0488 in.)
Intermediate shaft end play
Standard
0.022 to 1.099 mm (0.000867 to 0.0432 in.)
Planetary sun gear inside diameter
Standard
25.525 to 25.546 mm (1.00492 to 1.00575 in.)
Maximum
25.546 mm (1.0057 in.)
Rear planetary sun gear inside diameter
Standard
25.580 to 25.601 mm (1.00708 to 1.00791 in.)
Maximum
25.601 mm (1.0079 in.)
Under drive planetary gear clearance
Standard
0.18 to 0.54 mm (0.00709 to 0.0213 in.)
2nd brake piston return spring free length
Standard
23.26 mm (0.916 in.)
1st and reverse brake return spring free length
Standard
15.79 mm (0.621 in.)
No. 3 brake piston return spring free length
Standard
9.15 mm (0.360 in.)
No. 1 brake clearance
Standard
0.601 to 0.819 mm (0.0237 to 0.0322 in.)
No. 1 brake flange thickness
Thickness
Mark
3.0 mm (0.118 in.)
30
3.1 mm (0.122 in.)
31
3.2 mm (0.126 in.)
32
3.3 mm (0.130 in.)
33
3.4 mm (0.134 in.)
34
3.5 mm (0.138 in.)
35
No. 2 brake clearance
Standard
0.884 to 1.196 mm (0.0348 to 0.0471 in.)
No. 2 brake flange thickness
Thickness
Mark
4.0 mm (0.157 in.)
40
4.1 mm (0.161 in.)
41
4.2 mm (0.165 in.)
42
4.3 mm (0.169 in.)
43
4.4 mm (0.173 in.)
44
No. 3 brake clearance
Standard
0.599 to 0.799 mm (0.0236 to 0.0315 in.)
No. 3 brake flange thickness
Thickness
Mark
3.8 mm (0.150 in.)
38
3.9 mm (0.154 in.)
39
4.0 mm (0.157 in.)
40
4.1 mm (0.161 in.)
41
4.2 mm (0.165 in.)
42
4.3 mm (0.169 in.)
43
No. 1 clutch clearance
Standard
0.601 to 0.819 mm (0.0237 to 0.0322 in.)
No. 2 clutch clearance
Standard
0.544 to 0.744 mm (0.0214 to 0.0293 in.)
Manual valve lever shaft oil seal tap in depth
Standard
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Counter drive gear Preload
Standard
0.1 to 0.8 N*m (1 to 8 kgf*cm, 1 to 7 in.*lbf)
Counter driven gear Preload
Standard
Differential side bearing preload
+ 2.85 to 6.13 N*m (29.07 to 62.50 kgf*cm, 25.23 to 54.25 in.*lbf)
Adjust shim thickness
Thickness
2.000 mm (0.0787 in.)
2.025 mm (0.0797 in.)
2.050 mm (0.0807 in.)
2.075 mm (0.0817 in.)
2.100 mm (0.0827 in.)
2.125 mm (0.0837 in.)
2.150 mm (0.0846 in.)
2.175 mm (0.0856 in.)
2.200 mm (0.0866 in.)
2.225 mm (0.0876 in.)
2.250 mm (0.0886 in.)
2.275 mm (0.0896 in.)
2.300 mm (0.0906 in.)
2.325 mm (0.0915 in.)
2.350 mm (0.0925 in.)
2.375 mm (0.0935 in.)
2.400 mm (0.0945 in.)
2.425 mm (0.0955 in.)
2.450 mm (0.0965 in.)
2.475 mm (0.0974 in.)
2.500 mm (0.0984 in.)
2.525 mm (0.0994 in.)
2.550 mm (0.100 in.)
2.575 mm (0.101 in.)
2.600 mm (0.102 in.)
2.625 mm (0.103 in.)
2.650 mm (0.104 in.)
2.675 mm (0.105 in.)
2.700 mm (0.106 in.)
2.725 mm (0.107 in.)
2.750 mm (0.108 in.)
2.775 mm (0.109 in.)
2.800 mm (0.110 in.)
2.825 mm (0.111 in.)
2.850 mm (0.112 in.)
2.875 mm (0.113 in.)
2.900 mm (0.114 in.)
2.925 mm (0.115 in.)
2.950 mm (0.116 in.)
2.975 mm (0.117 in.)
3.000 mm (0.118 in.)
Transaxle rear cover bearing installation depth
Standard
21.5 to 21.9 mm (0.846 to 0862 in.)
Oil pump body clearance
Standard
0.075 to 0.145 mm (0.00296 to 0.00570 in.)

Maximum
0.145 mm (0.00570 in.)
Oil pump side clearance
Standard
0.025 to 0.040 mm (0.000985 to 0.00157 in.)

Maximum
0.04 mm (0.00157 in.)
Drive gear thickness
Thickness
Mark
11.547 to 11.555 mm (0.4546 to 0.4549 in.)
1
11.555 to 11.563 mm (0.4549 to 0.4552 in.)
2
11.564 to 11.571 mm (0.4553 to 0.4556 in.)
3
11.572 to 11.579 mm (0.4556 to 0.4559 in.)
4
11.580 to 11.587 mm (0.4559 to 0.4562 in.)
5
Driven gear thickness
Thickness
Mark
11.547 to 11.555 mm (0.4546 to 0.4549 in.)
1
11.555 to 11.563 mm (0.4549 to 0.4552 in.)
2
11.564 to 11.571 mm (0.4553 to 0.4556 in.)
3
11.572 to 11.579 mm (0.4556 to 0.4559 in.)
4
11.580 to 11.587 mm (0.4559 to 0.4562 in.)
5
Oil pump body bushing inside diameter
Standard
43.135 to 43.160 mm (1.6983 to 1.6922 in.)
Maximum
43.160 mm (1.6922 in.)
Stator shaft bushing inside diameter
Standard
22.500 to 22.526 mm (0.88583 to 0.88684 in.)
Maximum
22.570 mm (0.88858 in.)
Differential side gear backlash
Standard
0.05 to 0.2 mm (0.00197 to 0.00787 in.)
Thrust washer thickness
Thickness
1.00 mm (0.0394 in.)
1.10 mm (0.0433 in.)
1.20 mm (0.0472 in.)
1.30 mm (0.0512 in.)
Differential side bearing Preload
Standard
0.89 to 1.31 N*m (9.08 to 13.35 kgf*cm, 7.88 to 11.59 in.*lbf)
Adjust shim thickness
Thickness
2.000 mm (0.0787 in.)
2.025 mm (0.0797 in.)
2.050 mm (0.0807 in.)
2.075 mm (0.0817 in.)
2.100 mm (0.0827 in.)
2.125 mm (0.0837 in.)
2.150 mm (0.0846 in.)
2.175 mm (0.0856 in.)
2.200 mm (0.0866 in.)
2.225 mm (0.0876 in.)
2.250 mm (0.0886 in.)
2.275 mm (0.0896 in.)
2.300 mm (0.0906 in.)
2.325 mm (0.0915 in.)
2.350 mm (0.0925 in.)
2.375 mm (0.0935 in.)
2.400 mm (0.0945 in.)
2.425 mm (0.0955 in.)
2.450 mm (0.0965 in.)
2.475 mm (0.0974 in.)
2.500 mm (0.0984 in.)
2.525 mm (0.0994 in.)
2.550 mm (0.100 in.)
2.575 mm (0.101 in.)
2.600 mm (0.102 in.)
2.625 mm (0.103 in.)
2.650 mm (0.104 in.)
2.675 mm (0.105 in.)
2.700 mm (0.106 in.)
2.725 mm (0.107 in.)
2.750 mm (0.108 in.)
2.775 mm (0.109 in.)
2.800 mm (0.110 in.)
2.825 mm (0.111 in.)
2.850 mm (0.112 in.)
2.875 mm (0.113 in.)