Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM

BLOCKING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TELEPHONE TRANSCEIVER ASSEMBLY

B236628E05

  1. Disconnect the I70 telephone transceiver assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I70-6 (IG2) - I70-9 (E)
    LG - BR
    Ignition power supply
    Engine switch on (IG)
    9 to 16 V
    I70-12 (+B) - I70-9 (E)
    G - BR
    +B power supply
    Always
    9 to 16 V
    I70-9 (E) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I70 telephone transceiver assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I70-1 (BLK1) - I70-9 (E)
    L - BR
    Certification ECU (smart key ECU assembly) communication input
    Engine switch off
    11 to 14 V
    I70-1 (BLK1) - I70-9 (E)
    L - BR
    Certification ECU (smart key ECU assembly) communication input
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 1)
    I70-2 (BLK4) - I70-9 (E)
    Y - BR
    Certification ECU (smart key ECU assembly) communication output
    Engine switch off
    Below 1 V
    I70-2 (BLK4) - I70-9 (E)
    Y - BR
    Certification ECU (smart key ECU assembly) communication output
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 2)
    I70-7 (BLK2) - I70-9 (E)
    R - BR
    ECM communication output
    Engine switch off
    Below 1 V
    I70-7 (BLK2) - I70-9 (E)
    R - BR
    ECM communication output
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 1)
    I70-8 (BLK3) - I70-9 (E)
    G - BR
    ECM communication input
    Engine switch off
    Below 1 V
    I70-8 (BLK3) - I70-9 (E)
    G - BR
    ECM communication input
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 2)

    1. If the result is not as specified, the telephone transceiver assembly may have a malfunction.



  5. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      1. I70-1 (BLK1) - I70-9 (E)
      2. I70-7 (BLK2) - I70-9 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected



    2. Waveform 2 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      1. I70-2 (BLK4) - I70-9 (E)
      2. I70-8 (BLK3) - I70-9 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E17

  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A43-2 (+B) - A43-11 (E)
    W - W
    +B power supply
    Always
    11 to 14 V
    A43-10 (CUTB) - A43-11 (E)
    L - W
    Dark current cut pin
    Always
    11 to 14 V
    A43-11 (E) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the A43 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I78-5 (IG) - A43-11 (E)
    LG - W
    Ignition power supply
    Engine switch off → on (IG)
    Below 1 V → 11 to 14 V
    A43-14 (EFII) - A43-11 (E)
    G - W
    EFI communication input
    (Signal input from ECM to certification ECU (smart key ECU assembly))
    Engine switch off
    11 to 14 V
    A43-13 (EFIO) - A43-11 (E)
    Y - W
    EFI communication output
    (Signal output from certification ECU (smart key ECU assembly) to ECM)
    Engine switch off
    Below 1 V

  5. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A43-14 (EFII) - A43-11 (E)
    G - W
    EFI communication input
    (Signal input from ECM to certification ECU (smart key ECU assembly))
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 1)
    A43-13 (EFIO) - A43-11 (E)
    Y - W
    EFI communication output
    (Signal output from certification ECU (smart key ECU assembly) to ECM)
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 2)

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.



  6. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A43-14 (EFII) - A43-11 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected



    2. Waveform 2 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A43-13 (EFIO) - A43-11 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


CHECK ECM

A247842E16

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage or resistance for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E26-49 (E1) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
A25-1 (BATT) - E26-49 (E1)
GR - BR
+B power supply
Always
11 to 14 V
A25-2 (+B) - E26-49 (E1)
P - BR
+B power supply
Engine switch on (IG)
11 to 14 V
A25-3 (+B2) - E26-49 (E1)
LG - BR
+B power supply
Engine switch on (IG)
11 to 14 V
A25-30 (IMO) - E26-49 (E1)
G - BR
Certification ECU (smart key ECU assembly) communication input
Engine switch off
Below 1 V
A25-30 (IMO) - E26-49 (E1)
G - BR
Certification ECU (smart key ECU assembly) communication input
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
Pulse generation
(See waveform 1)
A25-31 (IMI) - E26-49 (E1)
Y - BR
Certification ECU (smart key ECU assembly) communication output
Engine switch off
Below 1 V
A25-31 (IMI) - E26-49 (E1)
Y - BR
Certification ECU (smart key ECU assembly) communication output
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
Pulse generation
(See waveform 2)


  1. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A25-30 (IMO) - E26-49 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected



    2. Waveform 2 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A25-31 (IMI) - E26-49 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected