Home › Steering › STEERING COLUMN › STEERING PAD SWITCH

STEERING PAD SWITCH > INSPECTION

for Preparation Click here



1. INSPECT STEERING PAD SWITCH ASSEMBLY (except Audio and Visual System (for Radio Receiver Type))


  1. Measure the resistance according to the value(s) in the table below.


    E225611E02

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (HO) - Terminal-A
    Always
    Below 1 Ω
    2 (+DP) - 3 (-DP)*1
    No switch pushed
    95 to 105 kΩ
    DISP switch pushed
    Below 2.5 Ω
    11 (AU1) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Up switch pushed
    Below 2.5 Ω
    Down switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    10 (AU2) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω
    On hook switch pushed
    313 to 345 Ω
    Off hook switch pushed
    950 to 1050 Ω
    Voice switch pushed*2
    2955 to 3265 Ω
    9 (AU3) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Enter switch pushed
    Below 2.5 Ω
    Back switch pushed
    313 to 345 Ω
    Right switch pushed
    950 to 1050 Ω
    Left switch pushed
    2955 to 3265 Ω

    1. *1: w/ DISP Switch of Steering Pad Switch Assembly
    2. *2: w/ Voice Switch of Steering Pad Switch Assembly

    HINT:
    If the result is not as specified, replace the steering pad switch assembly.


    Text in Illustration 
    *A
    w/ Voice Switch of Steering Pad Switch Assembly
    *B
    w/ DISP Switch of Steering Pad Switch Assembly
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Volume+
    *c
    Volume-
    *d
    Back
    *e
    MODE/HOLD
    *f
    Up
    *g
    Down
    *h
    Left
    *i
    Right
    *j
    Enter
    *k
    Off hook
    *l
    On hook
    *m
    Voice
    *n
    DISP
    *o
    Terminal-A
    -
    -



  1. Check the illumination.


    E230752E01


    1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      HINT:
      If the result is not as specified, replace the steering pad switch assembly.


      Text in Illustration 
      *a
      Component without harness connected
      (Steering Pad Switch Assembly)
      -
      -



2. INSPECT STEERING PAD SWITCH ASSEMBLY (for Audio and Visual System (for Radio Receiver Type))


  1. Measure the resistance according to the value(s) in the table below.


    E224424E02

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (HO) - Terminal-A
    Always
    Below 1 Ω
    11 (AU1) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    10 (AU2) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω
    On hook switch pushed
    313 to 345 Ω
    Off hook switch pushed
    950 to 1050 Ω

    HINT:
    If the result is not as specified, replace the steering pad switch assembly.


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Volume+
    *c
    Volume-
    *d
    Seek-
    *e
    Seek+
    *f
    MODE/HOLD
    *g
    Off hook
    *h
    On hook
    *i
    Terminal-A
    -
    -



  1. Check the illumination.


    E231452E01


    1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      HINT:
      If the result is not as specified, replace the steering pad switch assembly.


      Text in Illustration 
      *a
      Component without harness connected
      (Steering Pad Switch Assembly)
      -
      -



3. INSPECT STEERING PAD SWITCH LH (for Audio and Visual System (for Radio Receiver Type))


  1. Measure the resistance according to the value(s) in the table below.


    E224426E02

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (HO) - Terminal-A
    Always
    Below 1 Ω
    2 (+DP) - 3 (-DP)
    No switch pushed
    95 to 105 kΩ
    DISP switch pushed
    Below 2.5 Ω
    11 (AU1) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    10 (AU2) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω

    HINT:
    If the result is not as specified, replace the steering pad switch LH.


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch LH)
    *b
    Volume+
    *c
    Volume-
    *d
    Seek-
    *e
    Seek+
    *f
    MODE/HOLD
    *g
    DISP
    *h
    Terminal-A



  1. Check the illumination.


    E231453E01


    1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch LH connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      HINT:
      If the result is not as specified, replace the steering pad switch LH.


      Text in Illustration 
      *a
      Component without harness connected
      (Steering Pad Switch LH)
      -
      -